Prògramadair Modúl XTOOL X2MBIR
Àicheadh
Please read this manual carefully before using X2Prog Module Programmer (herein after referred to as X2Prog). Shenzhen Xtooltech Intelligent Co., Ltd. (herein after referred to as “Xtooltech”) does not assume any liability in case of misuse of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice.
Tuairisgeul toraidh
’S e Prògramadair Modalan a th’ ann an X2Prog as urrainn dàta EEPROM agus sliseagan MCU a leughadh, a sgrìobhadh agus atharrachadh tro dhòigh BOOT. Tha an inneal seo freagarrach do luchd-gleusaidh no meacanaig charbadan proifeasanta, a bheir seachad gnìomhan leithid clònadh modalan, atharrachadh, no ath-chur airson ECU, BCM, BMS, deas-bhòrd no modalan eile. Tha X2Prog cuideachd comasach air modalan leudachaidh eile a tha air an toirt seachad le Xtooltech, a’ comasachadh barrachd ghnìomhan leithid prògramadh BENCH, còdadh transponder agus mòran a bharrachd.
Bathar View
- ① DB26 Port: Use this port to connect with cables or wiring harnesses.
- ② Indicators: 5V (Red / Left): This light will be turned on when X2Prog receives 5V power input. Communication (Green / Middle): This light will be flashing when the device is communicating. 12V (Red / Right): This light will be turned on when X2Prog receives 12V power input.
- ③ ④ Expansion Ports: Use these ports to connect with other expansion modules.
- ⑤ 12V DC Power Port: Connect to 12V power supply when necessary.
- ⑥ USB Type-C Port: Use this USB port to connect with XTool devices or PC.
- ⑦ Nameplate: Show product information.
Riatanasan inneal
- XTool devices: APP version V5.0.0 or higher;
- PC: Windows 7 no nas àirde, 2GB RAM
Ceangal inneal
Leudachadh & Ceangal Càball
X2Prog is adapted to various expansion modules or cables for extra functions. Different modules are needed in different situations.
To install expansion modules, directly connect the modules to X2Prog using the expansion ports (32/48PIN) or the DB26 port.
Multiple expansion modules can be installed on X2Prog at the same time. When you are operating, check the device and see which modules are necessary.
Mar a leughas is a sgrìobhas tu EEPROM
Tro Bhòrd EEPROM
*EEPROM Board only comes with X2Prog standard pack.
When reading EEPROM in this method, the chip should be taken off from the ECU and needs to be soldered onto the EEPROM board.
Tha dòighean eile ann airson EEPROM a leughadh le bhith a’ cleachdadh mhodalan leudachaidh. Thoir sùil air na diagraman air an aplacaid agus faic mar as urrainn dhut ceangal ris a’ chip.
Mar a leughas is a sgrìobhas tu MCUn
BOOT
When reading MCU in this method, the wiring harness should be soldered to the ECU board according to the wiring diagram, and a 12V power supply should be connected to X2Prog.
Nuair a bhios tu a’ leughadh MCU san dòigh seo, bu chòir an acfhainn uèiridh a bhith ceangailte ris a’ phort ECU a rèir an diagram uèiridh, agus bu chòir solar cumhachd 12V a bhith ceangailte ri X2Prog.
Cuir fios thugainn
- Seirbheisean teachdaiche:
taic@xtooltech.com - Oifigeil Weblàrach:
https://www.xtooltech.com/ - Seòladh:
17&18/F, Togalach A2, Cathair Cruthachail, Liuxian Avenue, Sgìre Nanshan, Shenzhen, Sìona - Corporate & Business:
margaidheachd@xtooltech.com
© Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, All Rights Reserved
Fiosrachadh Gèilleadh
Gèilleadh FCC
FCC ID: 2AW3IM604
Tha an inneal seo a’ cumail ri Pàirt 15 de Riaghailtean FCC. Tha gnìomhachd an urra ris an dà chùmhnant a leanas:
- Is dòcha nach toir an inneal seo bacadh cronail
- Feumaidh an inneal seo gabhail ri bacadh sam bith a gheibhear, a’ toirt a-steach bacadh a dh’ fhaodadh gnìomhachd neo-mhiannach adhbhrachadh.
Rabhadh
Dh’ fhaodadh atharrachaidhean no atharrachaidhean nach deach aontachadh gu sònraichte leis a’ phàrtaidh le uallach airson gèilleadh ùghdarras an neach-cleachdaidh airson an uidheamachd obrachadh a chuir am falach.
Thoir an aire
Chaidh an uidheamachd seo a dhearbhadh agus chaidh a lorg gu bheil e a rèir nan crìochan airson inneal didseatach Clas B, a rèir Pàirt 15 de Riaghailtean FCC. Tha na crìochan sin air an dealbhadh gus dìon reusanta a thoirt seachad an aghaidh bacadh cronail ann an ionad còmhnaidh.
This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Ath-stiùireadh no gluasad an antenna a tha a 'faighinn.
- Meudaich an dealachadh eadar an uidheamachd agus an cuidhteas.
- Ceangail an uidheamachd ri ar-a-mach air cuairt a tha eadar-dhealaichte bhon fhear ris a bheil an cuidhteas ceangailte.
- Bruidhinn ris an neach-reic no teicneòlaiche rèidio / Tbh eòlach airson cuideachadh.
Aithrisean Rabhadh Nochdaidh RF:
Bidh an uidheamachd seo a’ gèilleadh ri crìochan nochdaidh rèididheachd FCC a chaidh a mhìneachadh airson àrainneachd gun smachd. Thèid an uidheamachd seo a chuir a-steach agus obrachadh leis an astar as lugha 20cm eadar an radiator & body.
Pàrtaidh cunntachail
- Company name: TianHeng Consulting, LLC
- Seòladh: 392 Sràid Andover, Wilmington, MA 01887, Na Stàitean Aonaichte
- Post-d: tianhengconsulting@gmail.com
Aithris IED
- IC: 29441-M604
- PMN: M604, X2MBIR
- HVIN: M604
Anns an inneal seo tha inneal-sgaoilidh (ean) / cuidhteas (ean) gun chead a tha a’ gèilleadh ri RSS(ean) gun chead Ùr-ghnàthachadh, Saidheans agus Leasachadh Eaconamach Canada.
CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
Dearbhadh co-chòrdalachd
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
RACA
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.
Ceistean Cumanta
- C: Dè na riatanasan inneal a th’ ann airson Modúl X2MBIR a chleachdadh Prògramadair?
A: The X2MBIR Module Programmer requires XTool devices with APP version V5.0.0 or higher and a PC running on Windows 7 or higher with a minimum of 2GB RAM. - C: Ciamar a leughas is a sgrìobhas mi dàta EEPROM leis an X2Prog?
A: To read and write EEPROM data, use the provided EEPROM Board included in the standard pack. Remove the chip from the ECU and solder it onto the EEPROM board. - C: An urrainn dhomh iomadh modal leudachaidh a chleachdadh aig an aon àm leis an X2Prog?
A: Yes, multiple expansion modules can be installed on X2Prog at the same time. Ensure you connect them correctly to enhance functionality.
Sgrìobhainnean/Goireasan
 |
Prògramadair Modúl XTOOL X2MBIR [pdfStiùireadh Cleachdaiche M604, Prògramadair Modúl X2MBIR, X2MBIR, Prògramadair Modúl, Prògramadair |