Leabhar-stiùiridh Siostam Brosnachaidh TriggerTech KC0E ACE

Siostam Brosnachaidh TriggerTech KC0E ACE

Fiosrachadh toraidh

• The ACE Trigger System is designed for use with Glock Gen 1-5 pistols chambered in 9mm or .40 S&W.
• It is engineered to provide a smooth and consistent trigger pull, enhancing the overall shooting experience.

Stiùireadh stàlaidh

• Dèan cinnteach gu bheil an gunna-teine ​​agad gun luchdachadh agus sàbhailte airson obrachadh leis.
• Lean a h-uile rabhadh sàbhailteachd a tha air a mhìneachadh ann an leabhar-làimhe an neach-cleachdaidh.
• Consult a licensed gunsmith or contact TriggerTech for assistance if needed.
• Carefully install the ACE Trigger System according to the provided instructions.
• Test the functionality of the trigger system before using the firearm.

Stiùireadh Cleachdaidh

• When using the ACE Trigger System, always follow proper firearm safety protocols.
• Ensure that you are familiar with the handling of firearms and trigger components before installation.
• Any modifications should be done by a qualified professional.

Disclaimer, Limited Warranty, Satisfaction Guarante, Installation Instructions

RABHADH: Failure to properly install your trigger and ensure proper safety functionality could result in an unsafe rearm. Read and follow all instructions. Contact TriggerTech or a licensed gunsmith for assistance.

Àicheadh TriggerTech
Improper handling, installation, storage and/or use of TriggerTech products and/or the firearm in which they are installed can cause death, serious injury, and/or property damage.
Tha toraidhean TriggerTech air an dealbhadh a-mhàin airson an stàladh agus an cleachdadh anns an armachd-teine sònraichte air a bheil iad air an sanasachadh. Tha e an urra ris a’ cheannaiche co-chòrdalachd a dhearbhadh.
Faodaidh làimhseachadh is stàladh brosnachaidhean às dèidh a’ mhargaidh a bhith a’ toirt a-steach modhan-obrach toinnte agus a’ gabhail ris gum feumar eòlas fhaighinn air làimhseachadh ghunnaichean-teine. Mura h-eil ceannaiche no neach-cleachdaidh eòlach, no eòlach gu leòr, air làimhseachadh ghunnaichean-teine ​​agus iomlaid phàirtean brosnachaidh, faodaidh an ceannaiche no an neach-cleachdaidh (gu coitcheann,
feumaidh “Ceannaiche”) tuilleadh fiosrachaidh agus cobhair iarraidh bho ghunnaiche no bho phroifeasanta teisteanasach eile.
By installing or using any purchased TriggerTech trigger product (“TT Product”), the Purchaser agrees to the following terms and conditions:

1. The Purchaser will abide by all applicable firearm safety laws, protocols, and regulations in force in the jurisdiction where the TT Product is handled, installed, stored and/or used;
2. The Purchaser certifies that he/she is legally entitled to purchase and use the TT Product and the firearm in which it is to be installed, in the jurisdiction where the TT Product is purchased and used;
3. The Purchaser assumes responsibility for ensuring that any users of the TT Product comply with these terms and conditions and with all applicable firearms safety protocols and regulations when handling, installing, storing and/or operating the TT Product;
4. The Purchaser agrees to conduct a test for proper trigger fit and function, before each use of the TT Product, with the firearm in which it is installed in an unloaded condition. Never assume the TT Product works without testing it;
5. The Purchaser agrees to consistently use a trigger lock on the installed TT Product, together with any related safety mechanism on the firearm in which the TT Product is installed.
6. The Purchaser agrees to contact TriggerTech immediately in the event of any change or loss of trigger function.
7. Following installation, the Purchaser will not conduct any maintenance of the TT Product that requires disassembly of the TT Product, in whole or in part
8. In no event shall TriggerTech be liable for any direct, indirect, incidental, special, consequential, or punitive damages arising from loss of life, personal injury and/or property damage, in connection with the use or misuse of the TT product, or the firearm in which the TT Product is installed;
9. TriggerTech is not responsible for the acts or omissions of the Purchaser resulting from a lack of training or knowledge of firearms handling, or failure to properly implement such training and knowledge
10. The Purchaser assumes the risk and all liability for death, injury, and loss and damage to persons or property caused by use or installation inconsistent with TriggerTech’s instructions, negligent or intentional use or misuse of the TT Product, or the firearm in which the TT Product is installed.

Barantas Earranta TriggerTech

TriggerTech warrants to the original retail purchaser that this TriggerTech product will be free from manufacturing and handling defects for thirty days after the original sale of the product, and from manufacturing defects for the life of the product. This warranty only applies if this product was manufactured and sold by TriggerTech. This warranty excludes conditions caused by excessive wear and tear, aggressive handling, unreasonable use, modifications, alterations, tampcleachdadh mì-iomchaidh, stàladh neo-iomchaidh, no factaran eile taobh a-muigh smachd TriggerTech. Ma dh’atharraicheas tu an toradh ann an dòigh sam bith, thèid am barantas seo a chur à bith. Chan eil am barantas cuibhrichte seo a’ buntainn ri coileanadh san àm ri teachd.
Chan eil ùghdarras aig riochdaire, neach-sgaoilidh no ath-reiceadair TriggerTech dleastanas no buailteachd sam bith eile a ghabhail os làimh a thaobh an toraidh, no teirmichean a’ bharantais seo atharrachadh.
THA GACH BARANTAS ACH A THA AIR A AINMEACHADH AN-SEO AIR AN DIÙLTADH, A’ GABHAIL A-STEACH BARANTASAN FO-THUAIRTEACH MU MARSANTACHD AGUS FREAGARACHD AIRSON ADHBHAR SÒNRAICHTE, CHUN NA h-ÌRE A THA CEADACHTE FON LAGH A THA IOMCHAIDH. THA GACH UALLACH AIRSON MILLTEANAS TACHARTAISEACH, PEANASACH, SÒNRAICHTE NO TOIRTEACH AIR AN DIÙLTADH GU SOILLEIR, CHUN NA h-ÌRE A THA CEADACHTE FON LAGH A THA IOMCHAIDH.
Chan eil TriggerTech a’ gabhail uallach sam bith a thig bho chall beatha, leòn pearsanta agus/no milleadh seilbh a thaobh cleachdadh, droch chleachdadh no atharrachadh toradh TT, no an armachd-teine ​​anns a bheil Toradh TT air a chuir a-steach.
Tha barantas air a làimhseachadh gu dìreach le TriggerTech, chan ann tron ​​lìonra luchd-reic againn. Gus còmhdach barantais fhaighinn, cuir fios thugainn gu dìreach aig an
àireamh/website below for a return authorization. The product alleged to be defective must be returned to TriggerTech for inspection. The cost of shipping to us is the customer’s responsibility. Any products determined by TriggerTech to require warranty coverage will be replaced or repaired, at TriggerTech’s sole option.

Thoir an aire: Dh’ fhaodadh stàladh an inneal-brosnachaidh TriggerTech agad barantas neach-dèanamh an airm-teine ​​agad a dhèanamh neo-dhligheach gu h-iomlan no ann am pàirt, mar sin feuch an toir thu sùil air neach-dèanamh an airm-teine ​​gus faighinn a-mach a bheil buaidh aig an stàladh air barantas an airm-teine ​​agad mus stàlaich thu an inneal-brosnachaidh.
Gealladh Sàsachd TriggerTech
Tha nas lugha de shnàgadh aig luchd-brosnachaidh TriggerTech na toraidhean farpaisich. Ged a tha a’ mhòr-chuid de luchd-losgaidh view seo mar bhuannachd, is dòcha nach bi cuid a’ faighinn tlachd às a’ fhaireachdainn shònraichte, bhrosnachail a tha aig inneal-brosnachaidh TriggerTech. Ma tha thu nad cheannaiche tùsail agus mura h-eil thu riaraichte leis a’ bhriseadh-snàimh neoni den inneal-brosnachaidh TriggerTech agad, faodaidh tu a thilleadh gu TriggerTech taobh a-staigh trithead (30) latha bho cheannach, anns a’ phacaid thùsail agus le dearbhadh ceannach. Cho fad ‘s nach eil milleadh air an inneal-brosnachaidh, bheir TriggerTech air ais prìs a’ cheannaich.
ÀICHEADH: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. or GLOCK Ges.mbH. TriggerTech is not affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.mbH. The use of “GLOCK” in this document is merely to outline how to install the TriggerTech Ace Trigger System in GLOCK pistols. For genuine GLOCK, Inc. and GLOCK Ges.mbH products and parts, visit www.glock.com.

Siostam Brosnachaidh TriggerTech ACE airson Glock

Detailed instructions, FAQ and videos: www.triggertech.com

Co-fhreagarrachd

• Tha Siostam Brosnachaidh ACE TriggerTech airson Glock co-chòrdail ris a h-uile ginealach frèam àbhaisteach de Glocks (1-5) ann an 9mm & .40 S&W. Is iad na modailean: G17, 17L, 19, 19x, 22, 23, 24, 26, 34, 35, 45, 47.
• Feumaidh tu taba beag a thoirt air falbh air an fhrèam airson Glocks Gen 5.
• Air sgàth atharrachaidhean ann an fulangas ann an cuid de fhrèamaichean, is dòcha gum bi feum air gunnaiche barrantaichte air a shuidheachadh agus a cheangal gus dèanamh cinnteach gu bheil sàbhailteachd an luamhain ag obair gu ceart.
• Chan eil TriggerTech air co-chòrdalachd le frèamaichean clòn a dhearbhadh.

Unload your firearm and disassemble it

• Read the TriggerTech Disclaimer and TriggerTech Lifetime Warranty prior to installation and use.
• Visually and physically confirm the firearm is unloaded while keeping the muzzle pointed in a safe direction at all times.
• Thoir air falbh an sleamhnag.

Remove the existing trigger

• Thoir air falbh am prìne (na prìnichean) brosnachaidh aghaidh, agus an uairsin am prìne brosnachaidh cùil.
• Remove the barrel lug and then the slide stop.

• Tog an inneal-brosnachaidh suas agus a-mach às a’ ghunna.

Install the TriggerTech Disconnect Module

• Thoir air falbh plàta cùil an fhactaraidh le bhith a’ cleachdadh an inneal prìne a tha air a ghabhail a-steach gus muinchill fànais a’ phrìne losgaidh a bhrùthadh sìos agus an uairsin thoir air falbh plàta còmhdach an t-sleamhnag.
• Stàlaich am modúl dì-cheangail TriggerTech le bhith a’ cleachdadh an inneal prìne gus muinchill fànais a’ phrìne losgaidh a bhrùthadh sìos, an uairsin slat an às-tharraing fhad ’s a shleamhnaicheas tu am modúl dì-cheangail suas is na àite.
• Bu chòir dhut cliog a chluinntinn nuair a bhios am plàta cùil na shuidhe agus nach urrainn dhut a shleamhnadh a-mach.

Thoir an aire: REQUIRED Gen 5 modification

• Gen 5 Glocks have a small plastic tab at the back of the frame. It must be removed for the ACE Trigger System to operate. The firearm WILL NOT be able to function unless the tab is removed.
• Use an edged tool to carefully cut the tab flush with the frame.

Install TriggerTech ACE Trigger System

• Carefully mount the transfer bar from the lever module into the slot of the sear module. The two parts should nest easily without using any force.
• Insert the lever module first, followed by the rear module, into the frame.
• Ath-stàlaich an stad sleamhnag agus clag a’ bharaille.
• Ath-stàlaich na prìnichean nan tuill fa leth.

Safety lever function verification

• Dearbhaich gu bheil an luamhan sàbhailteachd agad ag obair gu ceart. Dearbhaich gu fradharcach gu bheil sàbhailteachd an luamhan brosnachaidh agad a’ freagairt ris na dealbhan gu h-ìosal anns gach modh.

Sàbhailteachd an sàs

• Ma chuireas tu feachd aig mullach an luamhain (far a bheil e a’ coinneachadh ris an fhrèam a’ cleachdadh an inneil prìne), bu chòir don stad sàbhailteachd beantainn ris an fhrèam agus casg a chuir air a’ ghunna bho bhith a’ losgadh.

Sàbhailteachd air a dhì-cheangal

• Ma chuireas tu do mheur air an inneal-brosnachaidh mar as àbhaist agus ma thòisicheas tu a’ putadh air an inneal-brosnachaidh, bu chòir don stad sàbhailteachd am frèam a ghlanadh gun bhacadh.

Loisg

• Ma tharraingeas tu tron ​​bhalla agus ma chluinneas tu am prìne fàinne a’ leigeil ma sgaoil, bu chòir don stad-siubhail thairis a bhith a’ beantainn ris a’ fhrèam.

Fit to frame corrective action

• Ann an cuid de chùisean, air sgàth atharrachaidhean ann an fulangas air an fhrèam, dh’ fhaodadh sàbhailteachd an luamhain bacadh a chur cus agus adhbhrachadh gum bi an luamhan a’ faireachdainn steigeach no garbh nuair a thèid an luamhan a ghnìomhachadh. Is e a’ chiad cheum an siubhal ath-shuidheachaidh atharrachadh.
• Ma tha thu a’ faighinn eòlas air seo, bidh feum agad air cuideachadh bho Armachdair le teisteanas Glock gus an inneal-brosnachaidh a chuir air an fhrèam.
• To adjust the trigger reset position remove material from this tab using an abrasive tool. Only remove a small amount between fitting trials to mitigate lever-to-frame interference.

• Ma mhaireas an steigeadh, bu chòir beagan stuth a thoirt air falbh bhon stad sàbhailteachd an duilgheadas steigeadh a lughdachadh.
• Gus sàbhailteachd an luamhain atharrachadh gus am bi e iomchaidh don fhrèam, thoir air falbh an stuth ann an ceumannan beaga le bhith a’ cleachdadh file no inneal sgrìobach eadar na deuchainnean freagarrachd air an stad sàbhailteachd luamhan a tha air a chomharrachadh. Thoir air falbh an stuth riatanach a-mhàin gus obrachadh rèidh an luamhain a choileanadh.

• Ma mhaireas an duilgheadas, cuir fios gu seirbheis teachdaiche TriggerTech airson tuilleadh cuideachaidh aig taic@triggertech.com no gunnaiche teisteanasach.
• If the issue is resolved, then proceed with the function checks in Step 7 to verify that the lever safety is performing correctly.
• RABHADH: Do not attempt Step 6 without the assistance of a Glock Certified Armorer.
• RABHADH: Air sgàth atharrachaidhean a dh’ fhaodadh a bhith ann an fulangas frèam, tha e comasach gu bheil sàbhailteachd an luamhain a’ suathadh cus no nach eil e ag obair idir. NA CLEACHD Siostam Brosnachaidh ACE mura h-eil sàbhailteachd an luamhain ag obair gu ceart.

Sgrùdadh gnìomh

• Prior to using your firearm, perform the following tests without ammunition and confirm your firearm is unloaded and pointed in a safe direction at all times to confirm your installation was done correctly. If your pistol fails any of these tests, do not use your pistol and contact TriggerTech Support or take your pistol to a certified Glock Amorer.
• Dèan na deuchainnean a leanas leis an t-sleamhnag air a thoirt a-mach às a’ fhrèam:
• Sianal a’ Phrìne Losgaidh: Cum sàbhailteachd a’ phrìne losgaidh sìos le bàrr do mheòir, agus crathadh an sleamhnag gu làidir bho cheann gu ceann. Bu chòir dhut cluinntinn a’ phrìne losgaidh a’ gluasad gu saor ann an sianal a’ phrìne losgaidh. Dèan cinnteach nach eil am Modúl Dì-cheangail a’ cur bacadh air gluasad a’ phrìne losgaidh.
• Thoir sùil air sàbhailteachd luamhan an inneal-brosnachaidh le bhith a’ feuchainn ri luamhan sàbhailteachd a’ phrìne losgaidh a thogail suas. Bu chòir do shàbhailteachd luamhan an inneal-brosnachaidh am bàr gluasaid a bhacadh gus nach tuit an sear mura h-eil luamhan an inneal-brosnachaidh air a ghnìomhachadh.

RABHADH: Air sgàth atharrachaidhean a dh’ fhaodadh a bhith ann an fulangas frèam, tha e comasach gu bheil sàbhailteachd an luamhain a’ suathadh cus no nach eil e ag obair idir. NA CLEACHD Siostam Brosnachaidh ACE mura h-eil sàbhailteachd an luamhain ag obair gu ceart.

• Test reset – pull and hold the trigger, push down the transfer bar and you should hear an audible click which indicates reset has occurred. Release the trigger lever and the transfer bar should return up to its starting position.

• Firing Pin Safety Test: Hold the slide and pull the lug of the firing pin all the way to the rear of the slide and then ease it forward until it stops in contact with the firing pin safety. Then press the lug of the firing pin forward with your forefinger using moderate force. The firing pin must not move forward past the firing pin safety, and must not protrude from the breech face of the slide. If the firing pin safety fails to keep the firing pin from moving forward. DO NOT LOAD OR FIRE YOUR PISTOL. Instead, have it inspected and repaired by a Glock Certified Armorer.
• Firing Pin: Hold the slide with the muzzle end downward, and press the firing pin safety into the slide with your fingertip. The firing pin should move downward, and the tip of the firing pin should protrude from the breech face. (Note: On brand new pistols, you may need to apply light downward pressure to the rear of the firing pin lug with your finger to assist the firing pin in moving downward).
• Inspect the ejector to ensure that it is intact.

Dèan na deuchainnean a leanas leis an armachd-teine ​​​​gu tur cruinnichte.

• Cycle the slide to reset the trigger, and press the trigger. You should hear and feel the firing pin release.
• Cycle the slide, press and hold the trigger to the rear. While continuing to hold the trigger to the rear, cycle the slide, then release the trigger. The trigger should reset. Press the trigger to ensure the firing pin releases.
• Insert an EMPTY magazine into the pistol. Pull the slide fully to the rear; the slide should lock open.
• Dèan cinnteach gu bheil luamhan an inneal-brosnachaidh a’ gluasad gu saor agus nach eil e a’ beantainn ris a’ gheàrd-brosnachaidh. Cha bu chòir fuaim cliog a bhith ri chluinntinn.
• Once 7a-j have been successfully passed without ammunition, you can begin using ammunition at a range. Start with one round and slowly increase the number of live rounds in your magazine.

Tog suas, bris cuideam agus ath-shuidhich atharrachadh faireachdainn

Users can tune the take up, break weight and reset feel of the trigger to their individual preference. Included with your TriggerTech ACE Trigger System are three springs: a heavy take-up spring (pre-installed), a light take-up spring and a light plunger spring. Users can use different combinations of springs to find the right pull weight range and feel, then use our patented CLKR Technology™ to dial in their own setting.

Tha an inneal-brosnachaidh TriggerTech agad suidhichte faisg air meadhan an raoin cuideam tarraing a chaidh a shanasachadh leis an earrach togail throm air a chuir a-steach.
RABHADH: It is recommended to operate your trigger at or above factory settings. Exercise caution when adjusting your pull weight and repeat Step 7 prior to using live ammunition.

Atharrachadh cuideam tarraing – luamhan/fuaran togail

Your TriggerTech ACE Trigger System is pre-installed with the heavy take-up spring (silver), with a light take-up spring
(gold) included in the packaging. To change the spring in the lever, follow the steps below:

• Thoir air falbh an luamhan le bhith a’ putadh a-mach am prìne leis an inneal prìne luamhain a tha air a ghabhail a-steach.
• Thoir air falbh an t-earrach.
• Insert the new spring into the spring lever pocket of the trigger lever and engage the spring protrusion in the transfer bar
• Ath-stàlaich am prìne.

Atharrachadh cuideam tarraing - fuaran plunger

To change your factory plunger spring to the included TriggerTech ACE Trigger System light plunger spring (black):

• Thoir air falbh am plàta cùil (faic ceum 3a)
• Thoir air falbh slat teannachaidh an tarraing-às agus an co-chruinneachadh buailte.
• Brùth am plugair gus an inneal-tarraing a thoirt a-mach. Tuitidh e a-mach às an t-sleamhnag. Tuitidh am plugair a-mach cuideachd.
• Thoir air falbh an t-earrach a tha suidhichte anns a’ phlunger.
• Replace it with the ACE Trigger System plunger spring and press it firmly into the plunger so it is set in place and won’t fall out on its own.
• Reinstall the plunger and apply pressure on it inward to the slide while you put the extractor back in. Then reinstall the extension rod and striker assembly.
• Ath-stàlaich am plàta cùil.

Rabhadh atharrachaidh cuideam tarraing

• CUDROMACH: Your TriggerTech ACE Trigger System allows you to adjust your trigger pull weight. The set screw is located on top of the Sear Module and is set to near the middle of the advertised pull weight range. To adjust the pull weight, insert the supplied 5/64” Allen wrench. To increase pull weight, turn the set screw clockwise. Do not adjust your Sear Module more than 8 full rotations from the lowest pull weight.
• RABHADH: It is recommended to operate your trigger at, or above factory settings. Exercise caution when adjusting your pull weight and repeat Step 7 prior to using live ammunition.
• The TriggerTech ACE Trigger System has an adjustable take-up, break weight, and reset feel. The factory setting is near the middle of the advertised range. There is such a thing as a trigger that is too light to be considered safe. This weight will change depending on the specifics of the firearm, the experience of the shooter and the intended use case (how the gun and all of its components are operated/handled). TriggerTech strongly recommends that you get some trigger time on your TriggerTech trigger before adjusting the break weight below the factory setting (a trigger set at 4.0 lbs is safer than a trigger set at 2.5 lbs). As you reduce the pull weight of a TriggerTech ACE Trigger System, you are reducing the amount of spring tension in the trigger, and it is possible that you may reach a point where the trigger in a specific firearm is not safe for the intended use case and/or the shooter.
• The trigger’s pull weight should not suddenly change on its own. If it does, stop using it immediately and contact TriggerTech Support.
• Thathar a’ cur an cuimhne do luchd-losgaidh Riaghailtean Sàbhailteachd Ghunnaichean NRA a leantainn an-còmhnaidh.

Stiùireadh Cuideam Tarraing TriggerTech

Glanadh cumail suas

Your TriggerTech trigger is designed to operate maintenance-free and lubricant-free. It is recommended that you minimize the amount of oil and gun cleaning products that get in contact with the trigger.
Tha sinn a’ moladh gun tèid fuigheall a’ ghunna a chumail aig ìre as ìsle.
Ma tha thu den bheachd nach eil an inneal-brosnachaidh agad ag obair ceart air sgàth truailleadh, tha sinn a’ moladh gun gabh thu na ceumannan a leanas:

1. Dèan cinnteach gu bheil an gunna-teine ​​agad gun luchdachadh.
2. Racaich an sleamhnag, loisg an gunna tioram a-rithist is a-rithist.
3. If Step 2 is unsuccessful, remove your TriggerTech trigger from the frame and you can try to clean with compressed air and/or a grease-cutting agent that does not leave residue. We recommend lighter fluid, letting it dry, and blowing out the trigger with compressed air. Follow the TriggerTech Installation Instructions when reinstalling your trigger.
4. If Step 3 is unsuccessful, we do NOT recommend opening your trigger housing and suggest you contact TriggerTech and arrange to have your trigger serviced. Note: breaking the “void if removed” will indicate that you have opened your trigger and may void the Limited Warranty.

Ceistean?

• 1-888-795-1485 Taic@TriggerTech.com. www.TriggerTech.com

Ceistean Cumanta

• C: Dè bu chòir dhomh a dhèanamh ma thachras duilgheadasan sam bith agam leis an t-Siostam Brosnachaidh ACE?
  • A: If you experience any issues with the product, please contact TriggerTech directly for assistance. Do not attempt to modify or repair the trigger system yourself to avoid potential safety hazards.
• C: An cuir stàladh an inneal-brosnachaidh TriggerTech barantas neach-dèanamh an airm-teine agam às a leth?
  • A: Installation of aftermarket triggers may void part or all of your firearm manufacturer’s warranty. It is recommended to check with the firearm manufacturer before installing the trigger system to understand the impact on your warranty coverage.