SoliTek SOLID Series Solar Modules Installation Guide

SoliTek SOLID Series Solar Modules

Stiùireadh Cleachdaidh

• Read this guide entirely before installation.
• This document provides minimum requirements and recommendations for safe and successful installation of SoliTek PV modules and is necessary to retain compliance with IEC 61215, IEC 61730, and UL 61730 standards.
• This guide provides basic information on JSC SoliTek Cells SOLID series photovoltaic modules, including their installation and safe handling.
• All instructions should be read and understood before attempting installation. Contact your dealer or JSC SoliTek Cells for further information if needed.
• This documentation refers to the PV modules themselves and is not a comprehensive installation manual for personnel not specifically trained in PV modules.
• It serves as a general but strictly mandatory reference for the installer. Infringement or inaccurate observance of any clause in this documentation voids the warranty.
• The installer must understand and follow all applicable local, state, and federal regulations and standards for building construction, electrical design, fire, and safety.
• Check with local authorities for permitting requirements before installing or maintaining PV modules, and become familiar with mechanical and electrical requirements for photovoltaic systems.
• Mura leanar an stiùireadh san stiùireadh seo dh’ fhaodadh sin cron a dhèanamh air co-phàirtean an t-siostaim, luchd-obrach a chuir ann an cunnart, milleadh a dhèanamh air seilbh, no barantas a’ phannail a dhèanamh neo-dhligheach.
• Rooftop PV systems should only be installed on dwellings formally analyzed for structural integrity and confirmed to be capable of handling the additional weighted load of PV system components (including PV modules) by a certified building specialist or engineer.

RIAGHAILTEAN COITCHEANN

• Feuch an leugh thu an stiùireadh seo gu tur mus tèid an stàladh.
• Is e adhbhar na sgrìobhainn seo riatanasan agus molaidhean as ìsle a thoirt seachad airson stàladh sàbhailte agus soirbheachail de mhodalan SoliTek PV.
• Tha riatanasan anns an sgrìobhainn seo cuideachd a tha riatanach gus gèilleadh modal SoliTek PV a rèir inbhean IEC 61215, IEC 61730, UL 61730.
• Anns an iùl seo tha fiosrachadh bunaiteach mu mhodalan photovoltaic sreath SOLID JSC “SoliTek Cells”, an stàladh agus an làimhseachadh sàbhailte. Bu chòir a h-uile stiùireadh a leughadh agus a thuigsinn mus feuch thu ri stàladh. Ma tha ceist sam bith agad, cuir fios chun neach-reic agad no JSC “SoliTek Cells” airson tuilleadh fiosrachaidh.
• This documentation refers to the PV-modules themselves and is not meant to be a complete installation manual for personnel not specifically trained to PV-modules.
• It serves as a general but strictly mandatory reference for the Installer.
• Bidh briseadh no cumail ri mearachd sam bith de chlàs sam bith den phàipearan seo a’ falmhachadh a’ bharantas.
• Feumaidh an stàlaichear a h-uile riaghailt agus inbhean ionadail, stàite agus feadarail a thuigsinn agus a leantainn airson togail thogalaichean, dealbhadh dealain, teine ​​​​is sàbhailteachd, agus feumaidh e bruidhinn ri ùghdarrasan ionadail gus na riatanasan ceadachaidh iomchaidh a dhearbhadh mus feuch iad ri modalan PV a chuir a-steach no a chumail suas agus bu chòir dhaibh fàs eòlach air na riatanasan meacanaigeach is dealain airson siostaman photovoltaic.
• Mura leanar an stiùireadh san stiùireadh seo dh’ fhaodadh e cron a dhèanamh air co-phàirtean an t-siostaim, luchd-obrach a chuir ann an cunnart, milleadh a dhèanamh air seilbh, no barantas a’ phannail a dhèanamh neo-dhligheach.
• Cha bu chòir siostaman Rooftop PV a chuir a-steach ach air togalaichean a chaidh a sgrùdadh gu foirmeil airson iomlanachd structarail agus a chaidh a dhearbhadh gu bheil iad comasach air an luchd cuideam a bharrachd de cho-phàirtean siostam PV, a’ toirt a-steach modalan PV, a làimhseachadh le eòlaiche togalach le teisteanas no innleadair.
• For your safety, do not attempt to work on a rooftop until safety precautions have been identified and taken, including, without limitation fall protection measures, ladders or stairways, and personal protective equipment (PPE).
• For your safety, do not install or handle PV modules under adverse conditions, including, without limitation strong or gusty winds, and wet or frosted roof surfaces.
• Tha togail modal còmhnard PV air a dhèanamh suas de cho-chruinneachadh lannaichte de cheallan grèine air a chuairteachadh taobh a-staigh stuth inslithe taobh a-staigh dà dhuilleag glainne.
• Cùm na sgrìobhainnean seo ann an àite sàbhailte airson iomradh san àm ri teachd.
• Na feuch ris a’ mhodal a thoirt às a chèile, agus na thoir air falbh clàran-ainm no co-phàirtean ceangailte! Ma nì thu sin cuiridh e am barantas air falbh.

Làimhseachadh & Iarrtas

LAOIDH

• SoliTek PV modules must be transported in the supplied packaging only and kept in the packaging until they are ready to be installed.
• Protect pallets against movement and exposure to damage during transportation. Secure pallets from falling over.
• Na bi nas àirde na an àirde as àirde de pallets a thèid a chruachadh, mar a tha air a chomharrachadh air a’ phacaid màileid.
• Store pallets in a cool and dry location until the PV modules are ready to be unpackaged.
• SoliTek PV modules are heavy and should be handled with care. Never use the junction box or cables as a grip.
• Do not exert mechanical stress on the cables.
• Never step on PV modules or drop or place heavy objects on them.
• Be careful when placing PV modules on hard surfaces and secure them from falling.
• Broken glass can result in personal injury. PV modules with broken glass cannot be repaired and must not be used.
• Broken or damaged PV modules must be handled carefully and disposed of properly.

IARRTAS

Cuingeachaidhean

• SoliTek PV modules must be mounted on appropriate mounting structures positioned on suitable buildings, the ground, or other structures suitable for PV modules (e.g. carports, building facades or PV trackers).
• PV modules must not be mounted on moving vehicles of any kind. Modules must not be installed in locations where they could be submerged in water.
• Do not install modules above 2000 m (6561 ft) altitude above sea level
• Chan fhaod solas le fòcas fuadain a bhith air a stiùireadh air modalan SoliTek PV.

Molaidhean

• Tha SoliTek a’ moladh gun tèid modalan PV a chuir suas aig ceàrn teilt as ìsle de cheumannan 10 gus leigeil le fèin-ghlanadh ceart bhon uisge.
• Faodaidh sgàileadh pàirt no iomlan de mhodal no mhodalan PV coileanadh siostam a lughdachadh gu mòr.
• Tha SoliTek a’ moladh a bhith a’ lughdachadh na tha de sgàil tron ​​bhliadhna gus an ìre de lùth a thig bho na modalan PV a mheudachadh.
• Àrd siostam voltages could be induced in the event of an indirect lightning strike, which could cause damage to PV system components.
• The open area of wire loops should be minimized in order to reduce the risk of lightning-induced voltage ag èirigh.
• Bidh fionnarachadh mhodalan nas fheàrr agus càbaill ceangail nas giorra ag àrdachadh cinneasachadh lùth dealain.

Airson modalan dà-thaobhach:

• Thathas a 'moladh àirde pannal PV àrdachadh bhon talamh gus am faod barrachd solas siubhal fon mhodal agus an uairsin meòrachadh
• Bidh am buannachd dà-thaobhach a’ dol am meud gu mòr ma tha modalan air an cur a-steach os cionn uachdar geal (luach albedo àrd), a tha a’ nochdadh solas.

Stàladh dealain

SÀBHAILTEACHD

• Faodaidh modalan PV sruth agus voltage nuair a bhios e fosgailte do sholas de dhian sam bith. Bidh sruth dealain ag àrdachadh le dian solais nas àirde. DC voltage de 50 Volts no nas àirde a dh’ fhaodadh a bhith marbhtach. Ma chuireas tu fios gu cuairteachadh beò siostam PV a tha ag obair fo sholas faodaidh clisgeadh dealain marbhtach adhbhrachadh.
• Cuir às do mhodalan PV le bhith gan toirt air falbh gu tur bho sholas no le bhith a’ còmhdach an uachdar aghaidh le stuth neo-shoilleir. A thaobh riaghailtean sàbhailteachd airson uidheamachd dealain beò nuair a bhios tu ag obair le modalan a tha fosgailte do sholas sam bith. Cleachd innealan inslithe agus na bi a’ caitheamh seudaireachd meatailteach fhad ‘s a bhios tu ag obair le modalan PV.
• Gus arcing agus clisgeadh dealain a sheachnadh, na dì-cheangail ceanglaichean dealain fo luchd. Faodaidh ceanglaichean lochtach cuideachd leantainn gu arcing agus clisgeadh dealain. Cùm luchd-ceangail tioram agus glan agus dèan cinnteach gu bheil iad ann an staid obrach cheart. Na cuir a-steach stuthan meatailteach a-steach don luchd-ceangail no atharraich iad ann an dòigh sam bith gus ceangal dealain a dhèanamh tèarainte.
• Do not touch or handle PV modules with broken glass unless the PV modules are first disconnected, and you are wearing proper PPE. Avoid handling PV modules when they are wet unless cleaning the PV modules as directed in this manual. Never touch electrical and wet connections without protecting yourself with insulated gloves.
• The modules are qualified for Class II protection against electrical shock, in accordance with clause 4 of IEC 61730-1:2016, which can be used in systems operating at > 50 V DC or >240 W, where general contact access is anticipated and modules qualified for safety through UL 61730 within this application class are considered to meet the requirements of Safety Class II.
• Feumaidh stàladh siostaman grèine photovoltaic sgilean agus eòlas sònraichte. Bu chòir a dhèanamh a-mhàin le luchd-obrach le teisteanas agus le stiùireadh sònraichte. Bidh an stàlaichear a’ gabhail ris a h-uile cunnart bho leòn, a’ toirt a-steach cunnart clisgeadh dealain.
• Cleachd dìreach uidheamachd, luchd-ceangail, uèirleadh agus bathar-cruaidh sreap a chaidh a dhealbhadh gu sònraichte airson a chleachdadh ann an siostam photovoltaic.
• Before any manipulation at an installed PV plant, switch it off first on the AC-side, and then on the DC side of the inverter or the charge controller.
• Nuair a thèid uèirichean a dhì-cheangal ceangailte ri modal photovoltaic a tha fosgailte do sholas, faodaidh arc dealain tachairt. Faodaidh arcs losgadh adhbhrachadh, teintean a thòiseachadh, no duilgheadasan sàbhailteachd a chruthachadh (suas ri clisgeadh dealain marbhtach).
• Thoir sùil airson voltage before starting and observe the local safety-relevant regulations for such working conditions.
• Fo chumhachan àbhaisteach, faodaidh modal photovoltaic barrachd gnàthachadh agus / no voltage (an seo: 30V DC) na chaidh aithris aig suidheachaidhean deuchainn àbhaisteach.
• Cuir fios gu DC voltage de 30 V no barrachd a dh’ fhaodadh a bhith cunnartach. Bi faiceallach nuair a bhios tu a’ sreangadh no a’ làimhseachadh mhodalan a tha fosgailte do sholas na grèine.
• Na ceangail ach modalan leis an aon shruth toraidh ìre ann an sreath. Ma tha modalan ceangailte ann an sreath, bidh an leabhar iomlantage co-ionann ri suim a' mhodail fa leth voltagtha.
• Na ceangail ach modalan no measgachadh sreath de mhodalan leis an aon voltage in parallel. If modules are connected in parallel, the total current is equal to the sum of the individual module or series combination currents.
• Cleachd an-còmhnaidh an aon sheòrsa modal taobh a-staigh siostam photovoltaic sònraichte.
• If the sum of short circuit currents of the parallel-connected modules exceeds the reverse current, string diodes or fuses have to be used in each string of modules connected in parallel. These string diodes or fuses have to be qualified for the maximum expected current and voltage. The fuse rating value is also corresponds to the maximum reverse current that a module can withstand. The reverse current value can be found on the product label, in the product datasheet or in chapter 8 of the installation manual. Observe the instructions and safety precautions for all other components used in the system, including wiring and cables, connectors, DC-breakers, inverters, etc.
• Cleachd uidheamachd sàbhailteachd iomchaidh (innealan inslithe, miotagan dielectric, brògan is msaa) a chaidh aontachadh airson a chleachdadh air ionadan dealain.

CONFIGURATION

• Fo chumhachan àbhaisteach, tha coltas ann gum bi modal photovoltaic ann an suidheachaidhean a bheir toradh nas gnàthach agus / no voltage than reported at Standard Test Conditions (STC: 1000 W/ m2, AM 1.5, and 250C/770F cell temperature) or Bifacial nominal power index(BNPl front irradiance 1000 W/m2, back irradiance 135 W/m2 AM 1.5, and 25 OC/770F cell temperature). The short-circuit current (ISC) should be multiplied by a factor of 1.25 and the open-circuit voltagBu chòir e (VOC) a bhith air iomadachadh le factar suas gu 1.25 stèidhichte air an teòthachd àrainneachd as ìsle agus as àirde a chaidh a chlàradh airson an àite stàlaidh nuair a thathar a’ dearbhadh meud na co-phàirt.tage rangachadh, rangachadh sruth stiùiridh, meudan fiùs, agus meud smachdan ceangailte ri toradh PV.
• Voltagtha e cur-ris nuair a tha modalan PV ceangailte gu dìreach ann an sreath, agus tha sruthan mhodalan nan cur-ris nuair a tha modalan PV ceangailte gu dìreach ann an co-shìnte. Chan fhaod modalan PV le feartan dealain eadar-dhealaichte a bhith ceangailte gu dìreach ann an sreath. Faodaidh cleachdadh innealan dealanach treas-phàrtaidh iomchaidh ceangailte ri modalan PV diofar cheanglaichean dealain a chomasachadh agus feumar an stàladh a rèir stiùireadh ainmichte an neach-dèanamh.
• An vol as àirdetage of serial interconnection of the modules must be less than the maximum certified module’s system voltage. Cuideachd, an ìre as àirde a-steach voltagFeumar aire a thoirt don inneal-tionndaidh agus innealan dealain eile san t-siostam. Tha an cuairteachadh fosgailte voltage of the array string needs to be calculated at the lowest expected a mbient temperature forthe location. The maximal system voltage for the module is indicated in the module’s datasheet.
• Accordingly, for BLACKSTAR, SOLID or MAGNUS series modules, the values of ISC and VOC under STC or BNPI marked on this module should be multiplied by a factor of 1,25 when determining component voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output. In the USA, referto Section 690-8 of the National Electrical Code (N EC) for an additional multiplying factor of 125 percent (80 percent de-rating) which may be applicable.

INNLEAS DÌON A THA A-MHÀIN (OCPD)

• When the potential reverse current of a PV string exceeds the rated SoliTek PV module series fuse rating (values indicated at the module datasheet) an overcurrent protection device (OCPD) must be used.
• An overcurrent protection device is required for each series string if more than two series are connected in parallel.
• In this case, it is needed to use one fuse per string rated at 1.25 x Isc or higher (Isc is the PV module’s short circuit current at STC). A PV fuse on each PV string will protect the PV modules and conductors from overcurrent faults and help minimize any safety hazards.
• The PV fuse will also isolate the faulted PV string so the balance of the PV system can continue to generate electricity.
• fiùs amp rangachadh ≥ 1.25 x Isc
• Tagh an ath ìre àbhaisteach nas àirde aig a’ chatalog de PV Fuses a tha ri fhaighinn.
• Isc = sruth cuairt ghoirid de aon mhodal aig Cùmhnantan Deuchainn Coitcheann (STC).
• A’ beachdachadh air luachan mhodalan Isc de SoliTek, is e 30 A an luach ceart de na fuses PV a thèid a chleachdadh aig an stàladh.

CABLE & WIRING

Tha modalan SoliTek PV air an toirt seachad le dà chàball toraidh àbhaisteach a tha an aghaidh solas na grèine a tha air an crìochnachadh le luchd-ceangail PV deiseil airson a’ mhòr-chuid de ionadan. Tha ceanglaiche fireann aig a’ cheann-uidhe adhartach (+) fhad ‘s a tha ceangal boireann aig a’ cheann-uidhe àicheil (-). Tha sreangadh a’ mhodal an dùil airson ceanglaichean sreath (ie, fireann (+) gu eadar-cheangail boireann (-)) ach faodar a chleachdadh cuideachd gus innealan dealain treas-phàrtaidh iomchaidh a cheangal a dh’ fhaodadh a bhith aig rèiteachadh uèirleas eile fhad ‘s a thèid stiùireadh an neach-dèanamh a leantainn.
Cleachd uèirleadh achaidh le raointean tar-roinneil iomchaidh a tha ceadaichte airson an cleachdadh aig an ìre as àirde de chuairt ghoirid den mhodal PV. Feumaidh a h-uile uèirleadh a bhith le còmhdach dùbailte, càballan tar-cheangailte le ìre as ìsle de 1,8 kV (còrr air 1500 V voltage) agus an teòthachd as ìsle de 90 ˚C (190 °F). Meud uèir nach eil nas lugha na 4 mm² (12 AWG). Bu chòir an seòrsa insulation a bhith iomchaidh airson an seòrsa dòigh stàlaidh a thathar a’ cleachdadh agus feumaidh e coinneachadh ri riatanasan IEC 61730 agus Sàbhailteachd Clas II.

• Insulation ìre: 1,8 kV (conductor-conductor).
• Teòthachd: -40 ° C suas gu +90 ° C (-40 ° F suas gu 190 ° F) co-dhiù.
• Togail stiùiriche: uèir copar sìnte le snàithleach le purrachd copair nas motha na 99,9%.
• Insaladh bun-sgoile: polyethylene tar-cheangailte (XLPE), solas na grèine agus taiseachd-aghaidh, lasair-aghaidh. Freagarrach airson cladhan agus slighean-rèis air an stàladh fon talamh.
• Insaladh (seacaid): thermoplastic, solas na grèine, lasair-aghaidh, dìon-uisge.
• Trast-thomhas a-muigh càball as ìsle le insulation - 5,2 mm (2,05 òirleach).
• Tar-roinn stiùiridh as ìsle - 4 mm² (12 AWG).

Tha SoliTek a’ moladh nach bi luchd-stàlaidh a’ cleachdadh ach càbaill dìon-solas na grèine le teisteanas airson sreangadh sruth dhìreach (DC) ann an siostaman PV. Bu chòir càbaill a bhith air an ceangal ris an structar sreap ann an dòigh is gun tèid milleadh meacanaigeach air a’ chàball agus/no air a’ mhodal a sheachnadh. Na cuir cuideam air na càbaill. Airson càradh, cleachd dòighean iomchaidh, leithid ceangail càball a tha an aghaidh solas na grèine agus/no criomagan stiùireadh uèir. Ged a tha na càbaill an aghaidh solas na grèine agus uisge-dhìonach, ma ghabhas sin dèanamh, seachain solas dìreach bho sholas na grèine agus bogadh uisge nan càbaill.
Is e 1,2 m (47,24 òirleach) fad àbhaisteach nan càbaill bho na bogsaichean-ceangail. Thathar an dùil gum bi dà phannal ceangailte ri chèile san t-siostam.

FÀILTE

• Module grounding must be done in accordance with the electrical design and construction specifications, procedures, regulations and other special grounding requirements applicable to the installation sites. If grounding is needed, it should be done accordingly:

Framed type modules grounding
Chan urrainnear tuill a tha air an comharrachadh le comharra talmhainn air an fhrèam a chleachdadh ach airson a dhol air tìr. Na bi a 'drileadh tuill talmhainn a bharrachd air frèam a' mhodal.
The grounding conductor or strap may be copper, copper alloy, or any other material acceptable foruse as an electrical conductor in accordance with local electric codes and regulations.
Feumaidh an stiùiriche talmhainn an uairsin ceangal a dhèanamh ris an talamh le bhith a’ cleachdadh dealan talmhainn talmhainn iomchaidh.
A bolted connection is required; it incorporates:

• Meud bolt de M4.
• Feumaidh inneal-glanaidh fiacail fon cheann bolt no bolt serrated a dhol a-steach do chòmhdach neo-ghiùlain leithid frèam anodized.
• Cnò tapaidh a tha freagarrach airson bolt M4.
• Feumaidh a h-uile bathar-cruaidh a bhith de mheatailt neo-iarannach, de stàilinn gun staoin 300-sreath, no air a dhìon gu h-iomchaidh bho chreachadh.
• Is e an torque a thathar a’ moladh airson a’ chnò a ghlasadh 2 Nm÷2.2 Nm (1,48÷1,62 tr-lb).
• Feumaidh bolt talmhainn a dhol tro na h-eileamaidean ceangail gu lèir.

• Tha cead aig innealan a tha air an liostadh agus air an comharrachadh airson frèamaichean meatailteach de mhodalan PV a chuir sìos frèamaichean meatailteach fosgailte a’ mhodal a chuir gu structaran sreapachaidh stèidhichte.
• In any case the grounding screws or other parts have to be used separately from the mounting parts of the module.
• Alternate grounding options built through the mounting system are acceptable as long as they have been IEC and UL approved.
• Grounding resistance of the grounding structure shall be reached according to local regulations, Eurocodes, or other legal normative references.

Frameless type modules grounding

• Due to that modules are without frame, grounding is not forseen. Other PV plant equipment should be grounded according to the local and national electrical codes.

COMHAIRLEACHADH

• Connectors for SoliTek PV panels are Stäubli MC4-Evo 2. Keep connectors dry and clean and ensure that connector caps are hand-tight before connecting the modules.
• Na feuch ri ceangal dealain a dhèanamh le luchd-ceangail fliuch, salach no lochtach eile.
• Seachain solas na grèine agus bogadh uisge nan luchd-ceangail. Seachain luchd-ceangail a 'gabhail fois air an talamh no uachdar a' mhullaich.
• Do not disconnect under load. Faulty connections can result in arcs and electrical shock.
• Dèan cinnteach gu bheil a h-uile ceangal dealain ceangailte gu tèarainte. Dèan cinnteach gu bheil a h-uile ceangal glasaidh an sàs gu h-iomlan agus glaiste.

SEACHDADH DIODES

The PV module’s junction box contains 3 bypass diodes (one in each part of split junction box; Schottky type) connected in parallel with the PV cell strings. In the case of partial shading (hot-spot effect), the diodes bypass the current generated by the non-shaded cells, therebylimiting module heating and performance losses.
Chan e innealan dìon overcurrent a th’ ann an diodes seach-rathad. Bidh diodes seach-rathad a’ gluasad sruth bho na sreangan cealla ma tha pàirt dheth ann. Feartan nan diodes seo:

• Voltagìre e - 50 V.
• Ìre làithreach - 25 A.

RIAGHLADH CLANN TEINE

• Chaidh modalan SoliTek SOLID Bifacial agus Blackstar aontachadh le deuchainn teine ​​​​IEC agus choilean iad Clas Flammability A. Chaidh deuchainn teine ​​​​a dhèanamh aig claonadh 127 mm (5 òirleach) gach 300 mm (11,81 òirleach), mar a chaidh òrdachadh sa phuing A.2.5 de IEC 61730-2.
• SoliTek SOLID Bifacial has fire rating of 28 according to UL1703-2 standard. SoliTek Blackstar has fire rating of 29 according to UL1703-2 standard.

Stàladh meacanaigeach

• The mechanical loads described in this manual are the test loads.
• For calculating the equivalent maximum design loads, a safety factor of 1.5 (Design load×1.5 safety factor=Mechanical test load) needs to be considered in compliance with the requirements of the local laws and regulations.

RIAGHAILTEAN COITCHEANN

• Modules can be mounted in landscape or portrait orientation. For the bifacial modules, in order to get notable bifacial gain, the distance between the bottom of the modules and the roof or ground surface shall be at least 0,8 m (31,50 inch).
• Also, the bifacial gain increases significantly if modules are installed above white, light-reflecting surfaces (under surfaces with high albedo value).
• If the mounting rails are installed across the module, the bifaciality effect will be lower due to back-side cells shading.
• Feuch an cùm thu ris na riaghailtean sàbhailteachd agus an stiùireadh stàlaidh a tha an cois an t-siostam sreapachaidh. Ma tha feum air, cuir fios chun t-solaraiche gu dìreach airson tuilleadh fiosrachaidh.
• The modules must be safely set onto the mounting rail.
• The whole rail supporting the photovoltaic system must be strong enough to resist potential mechanical pressures caused either by wind or snow, in accordance with local, regional and state safety (and other associated) standards.
• The mounting system shall be tested and inspected by a third-party testing institution with static mechanical analysis capacity in accordance with local national standards or international standards.
• Before installing modules on a roof, ensure that the roof construction is suitable.
• In addition, any roof penetration required to mount the modules must be properly sealed to prevent leaks.
• Dèan cinnteach nach dèan an rèile sreapachaidh deformachadh no buaidh air na modalan nuair a bhios e a 'leudachadh mar thoradh air leudachadh teirmeach.
• The module can appear thermal expansion and cold contraction; thus, the interval between two adjoining modules shall be no lesser than 10 mm (0,39 inch).
• Na feuch ri drileadh tuill anns an uachdar glainne agus frèaman nam modalan oir cuiridh seo am barantas falamh.
• The mounting method must not result in the direct contact of dissimilar metals with the aluminum frame of the modules that will result in galvanic corrosion.

Feumaidh na pàirtean sreapachaidh a bhith air an dèanamh de stuthan seasmhach, an-aghaidh creimneach agus UV (thathas a’ moladh co-phàirtean stàilinn gun staoin agus alùmanum anodized).

A' MOLADH LE CLAMPS

• Cleachd co-dhiù 4 laminate clamps gus modalan a chàradh air na rèilichean sreap. Modalan clamps cha bu chòir pàirtean meatailt a dhol an conaltradh ris a’ ghlainne aghaidh no cùil. Nuair a thaghas tu an seòrsa seo de clamp-mounting dòigh, cleachd co-dhiù ceithir clamps air gach modal; dà clamps bu chòir a cheangal air gach taobh fhada. A rèir luchdan gaoithe is sneachda ionadail, clamps dh ’fhaodadh gum bi feum air dèanamh cinnteach gun urrainn do mhodalan an luchd a ghiùlan.
• Clamps bu chòir torque teannachaidh a bhith co-dhiù 15 Nm (11,06 tr-lb), ach gun a bhith nas àirde na 20 Nm (14,75 tr-lb). Mar as trice, ruigear 15 Nm (11,06 tr-lb), nuair a thèid dà alùmanum profiles suathadh a chèile. Nuair a thèid modal a chuir a-steach ann an stiùireadh dhealbhan air a ’mhullach claon aig a bheil leathad> 45 °, tha feum air dubhan a bharrachd aig bonn a’ mhodal.

SOLID Black, Semi-clear, Satin, Agro Frameless

Le rèilichean tarsainn

BLACKSTAR, SOLID Black 35(40) mm, SOLID Semi-clear 35(40) mm, SOLID Satin 35(40) mm, SOLID Agro 35(40) mm, Magnus Framed mounting

• Nuair a thaghas tu an seòrsa clamp-mounting dòigh, cleachd co-dhiù ceithir clamps air gach modal; dà clamps a bhith ceangailte air gach taobh den mhodal. Modalan clampcha bu chòir s a bhith a ’conaltradh ris a’ ghlainne aghaidh agus chan fhaod iad am frèam a dheformachadh.
• Dèan cinnteach gun seachain thu buaidhean dubhar air na ceallan grèine bhon mhodal clamps.
• The module frame is not to be modified under any circumstances. Do not to block the drain hole of the frame.
• Tha fad clamp should be at least 30 mm (1,18 inch).
• An clamp feumaidh iad a dhol thairis air frèam a’ mhodal le co-dhiù 5 mm (0,2 òirleach), ach gun a bhith nas fhaide na 10mm (0,4 òirleach).

Le rèilichean tarsainn

Às aonais rèilichean transversal no rèilichean tha ceart-cheàrnach ris an fhrèam taobh fhada

Le siostam cuir a-steach

Stàladh le boltaichean

• Feumaidh am modal a bhith ceangailte agus le taic bho cheithir boltaichean stàilinn stainless M8 tro na tuill sreap comharraichte air na bàraichean transversal. Torc air a' chlamp bolt has to be in range of 8÷10 Nm (5,9÷7,38 ft-lb). The transversal bars positioning is shown in Figure 3.
• If additional mounting points are required, depending on the local wind and snow loads, then a mounting solution with clampfeumar bathar-cruaidh a thaghadh.

• Mounting with bolts can be done only through dedicated predrilled holes in the frame.
• Tha e toirmisgte tuill ùra a dhrileadh agus fàgaidh e am barantas.

SEASAMH A' BHOG SHINN

• Airson an astar eadar bogsa snaim agus oir a’ mhodal no tomhasan eile de shuidheachadh bogsa snaim agus raointean thoir sùil air na figearan a chithear gu h-ìosal.

MOLADH

• Gus dèanamh cinnteach à coileanadh modal as fheàrr, tha SoliTek a’ moladh na leanas:
• Ma tha feum air, faodar aghaidh glainne a ’mhodal a ghlanadh le uisge agus spong bog no clò.
• Faodar inneal-glanaidh tlàth, neo-sgrìobach a chleachdadh gus stains nas gann a thoirt air falbh.
• Thoir sùil bho àm gu àm air na ceanglaichean dealain is meacanaigeach agus dèan cinnteach gu bheil iad glan, sàbhailte, coileanta agus tèarainte.
• Ma tha duilgheadas ann, bruidhinn ri neach le cead / teisteanas.

Sònrachaidhean

Table 9. Electrical and mechanical parameters table.

Table 10. Electrical and mechanical parameters table.

Table 11.Electrical and mechanical parameters table.

• The electrical characteristics are within of the indicated values of ISC (φISC) ±3%, VOC (ϕVOC) ±3,5% and PMPP (ϕPmax) ±5%, under Standard Test Conditions (STC) (irradiance of 1000 W/m²,AM 1.5 spectrum, and a cell temperature of 25°C / 77°F)
• Tha a h-uile pannal SoliTek SOLID PV a’ freagairt ri sàbhailteachd dealain clas II.

Àicheadh ​​buailteachd

• Leis gu bheil e do-dhèanta do SoliTek smachd a chumail air stàladh, obrachadh, cleachdadh agus cumail suas an t-siostam photovoltaic a rèir an stiùiridh seo. Cha bhith SoliTek a’ gabhail ri uallach agus gu sònraichte a’ diùltadh uallach airson call, milleadh no cosgais sam bith ag èirigh bho no ann an dòigh sam bith co-cheangailte ri leithid de stàladh, obrachadh, cleachdadh no cumail suas.
• SoliTek will not take any responsibility for any possible violation of patent rights and third-party rights that are related to the application of the solar energy system. No permission of patents is given through implication.
• The information of this instruction is from the knowledge and experiences of SoliTek. However, the instructions and suggestions of this instruction do not make an external or internal of guarantee. SoliTek reserves the right to revise this instruction, products and all the information about products without prior notification to customers.

www.soltek.eu

Ceistean Cumanta

• Q: What should I do before installing the PV modules?
  • A: Read this entire guide, understand all instructions, and ensure compliance with all local, state, and federal regulations. Consult a certified building specialist for the structural integrity of the dwelling.
• Q: Can I install the PV modules myself without professional training?
  • A: This documentation is not a complete installation manual for personnel not specifically trained in PV-modules. It serves as a general but strictly mandatory reference for the installer. Professional installation is highly recommended.
• Q: What happens if I don’t follow the instructions in this guide?
  • A: Failure to follow instructions may damage system components, endanger personnel, damage property, or invalidate the panel warranty.
• Q: Is it safe to work on a rooftop during installation?
  • A: Do not attempt to work on a rooftop until safety precautions have been identified and taken, including fall protection measures, ladders or stairways, and personal protective equipment (PPE). Avoid adverse conditions like strong winds or wet/frosted roofs.
• Q: How should I store the PV modules before installation?
  • A: Store pallets in a cool and dry location until the PV modules are ready to be unpackaged. Do not exceed the maximum stacking height indicated on the packaging.