Stiùireadh Obrachaidh M5StickC Plus2
Firmware factaraidh
Nuair a bhios duilgheadasan obrachaidh aig an inneal, faodaidh tu feuchainn ri bathar-bog an fhactaraidh ath-fhlasadh gus faicinn a bheil mearachd bathar-cruaidh ann. Thoir sùil air an oideachadh a leanas. Cleachd inneal frasaidh bathar-bog M5Burner gus am bathar-bog factaraidh a fhlasadh air an inneal.
Ceistean Cumanta
C1: Carson a tha an scrion dubh air an M5StickC Plus2 agam/nach tòisich e?
Fuasglaidhean: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
C2: Carson a tha e ag obair a-mhàin airson 3 uairean a thìde? Carson a bhios e a’ cosg 100% ann an 1 mhionaid, ma thogas tu a-mach an càball cosgais cuiridh e dheth e?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Please burn back official firmware.
Ullachadh
- Thoir sùil air an oideachadh M5Burner gus crìoch a chur air luchdachadh sìos an inneil flashing firmware, agus an uairsin thoir sùil air an ìomhaigh gu h-ìosal gus am firmware co-fhreagarrach a luchdachadh sìos.
Luchdaich sìos ceangal: https://docs.m5stack.com/en/uiflow/m5burner/intro
Stàladh an USB driver
Molaidhean airson stàladh draibhearan
Click the link below to download the driver matching your operating system. The driver package for the CP34X (for the CH9102 version) can be downloaded and installed by selecting the installation package corresponding to your operating system. If you encounter issues with program download (such as timeout or “Failed to write to target RAM” errors), try reinstalling the device driver.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Taghadh Puirt air MacOS
Air MacOS, dh’fhaodadh dà phort a bhith rim faighinn. Nuair a bhios tu gan cleachdadh, tagh am port leis an ainm wchmodem.
Taghadh Port
Ceangail an inneal ris a’ choimpiutair tro chàball USB. Às dèidh dhut an draibhear a stàladh, faodaidh tu am port inneil co-fhreagarrach a thaghadh ann am M5Burner.
Loisg
Briog air “Loisg” gus am pròiseas lasachaidh a thòiseachadh.
BataC-Plus2
SKU:K016-P2
Tuairisgeul
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Oideachadh
UIFlow
Seallaidh an oideachadh seo mar a chumas tu smachd air an inneal StickC-Plus2 tron àrd-ùrlar prògramaidh grafaigeach UIFlow.
UiFlow2
Seallaidh an oideachadh seo mar a chumas tu smachd air an inneal StickC-Plus2 tron àrd-ùrlar prògramaidh grafaigeach UiFlow2.
IDE Arduino
Seallaidh an oideachadh seo mar a nì thu prògramadh agus smachd air an inneal StickC-Plus2 a’ cleachdadh an Arduino IDE.
Thoir an aire
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Feartan
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Micreofon aonaichte
- User buttons, 1.14-inch LCD, power/reset button
- Bataraidh Li-ion 200 mAh
- Ceangal leudachaidh
- Integrated passive buzzer
- Wearable & mountable
- Àrd-ùrlar Leasachaidh
- UiFlow1
- UiFlow2
- IDE Arduino
- ESP-IDF
- Àrd-ùrlarIO
A’ toirt a-steach
- 1 x Bata C-Plus2
Iarrtasan
- Innealan a ghabhas caitheamh
- IoT controller
- STEM education
- Pròiseactan DIY
- Innealan dachaigh smart
Sònrachaidhean
| Sònrachadh | Paramadair |
| SoC | ESP32-PICO-V3-02 240 MHz dà-cridhe, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| Input Voltage | 5 V @ 500 mA |
| Eadar-aghaidh | Seòrsa-C x 1, GROVE (I2C + I/O + UART) x 1 |
| Sgrion LCD | 1.14 òirleach, 135 x 240 dath TFT LCD, ST7789V2 |
| Micreofon | SPM1423 |
| Putanan | Putanan cleachdaiche x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Buzzer | Buzzer fulangach air bòrd |
| IMU | MPU 6886 |
| Antenna | Antenna 2.4 G 3D |
| Binnean a-muigh | G0, G25/G26, G36, G32, G33 |
| Bataraidh | 200 mAh @ 3.7 V, a-staigh |
| Teòthachd Obrachaidh | 0 ~ 40 ° C |
| Dùnadh | Plastaig (PC) |
| Meud toraidh | 48.0 x 24.0 x 13.5mm |
| Cuideam toraidh | 16.7 g |
| Meud pacaid | 104.4 x 65.0 x 18.0mm |
| Cuideam Làn | 26.3 g |
Stiùireadh Obrachaidh
Cumhachd air / dheth
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Clàran
Mapa pin
LED Dearg & Sgaoileadair IR | Putan A | Putan B | Buzzer
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Putan A | Putan A | ||||
| Putan B | Putan B | ||||
| Putan C | Putan C | ||||
| Buzzer fulangach | Buzzer |
Taisbeanadh dath TFT
Driver IC: ST7789V2
Fuasgladh: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Taisbeanadh TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Micreofon MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | DÀTA |
IMU 6-Axis (MPU6886) & RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| IR Emitter | TX | ||
| LED dearg | TX |
HY2.0-4P
| HY2.0-4P | Dubh | Dearg | Buidhe | Geal |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Meud Modail
Bileagan dàta
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU 6886
SPM1423
Bathar-bog
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
Tòiseachadh Luath StickC-Plus2 UiFlow1
UiFlow2
Tòiseachadh Luath StickC-Plus2 UiFlow2
Àrd-ùrlarIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
frèam = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
Driver USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Ainm driver | Supported Chip | Luchdaich sìos |
| CH9102_VCP_SER_Windows | CH9102 | Luchdaich sìos |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | Luchdaich sìos |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Luchdaich sìos | Thoir an aire |
| Factory Test for Windows | luchdachadh sìos | / |
Eile
Stiùireadh Bathar-bog Factaraidh Ath-nuadhachaidh StickC-Plus2
Bhideo
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Atharrachadh Tionndadh
| Ceann-latha sgaoilidh | Atharraich Tuairisgeul | Thoir an aire |
| / | A’ chiad fhoillseachadh | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Coimeas toraidh
Eadar-dhealachaidhean bathar-cruaidh
| Bathar Ainm |
SoC | Stiùireadh cumhachd | Comas Bataraidh | Cuimhne | Sliseag USB-UART | Dath |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| BataC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Orains |
Eadar-dhealachaidhean prìne
| Ainm toraidh | IR | LED | TFT | CUNNTAS A | CUNNTAS B | PUTAN C (DÙISG) |
LAOIDH | Bataraidh Voltage A bhrath |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Gu riaghailteach putan |
/ | Tro AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Eadar-dhealachaidhean Cumhachd Air/Dheth
| Bathar Ainm | Cumhachd air adhart | Cumhachd dheth |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Leis gu bheil am PMIC AXP192 air a thoirt air falbh leis an StickC-Plus2, tha an dòigh-obrach airson a chumhachdachadh air/ dheth eadar-dhealaichte bho na dreachan roimhe. Mar a chaidh ainmeachadh aig toiseach na sgrìobhainn seo, tha an obrachadh gu ìre mhòr coltach, ach bidh na leabharlannan a tha a’ faighinn taic eadar-dhealaichte. Tha neart comharran Wi-Fi agus IR air an leasachadh an taca ris a’ mhodail roimhe.
Sgrìobhainnean/Goireasan
 |
Modúl Leasachaidh IoT M5STACK ESP32-PICO-V3-02 [pdfStiùireadh Cleachdaiche Modúl Leasachaidh IoT ESP32-PICO-V3-02, ESP32-PICO-V3-02, Modúl Leasachaidh IoT, Modúl Leasachaidh, Modúl |