Leabhar-stiùiridh airson inneal-atharrachaidh taidhrichean uisgeachaidh fèin-ghluasadach KATOOL KT-T900 & inneal-cothromachaidh cuibhle KT-B750

1. Toradh thallview

This manual provides essential information for the safe and efficient operation of your KATOOL KT-T900 Automatic Hydraulic Tire Changer and KT-B750 Automatic Measurement Ruler Wheel Balancer Combo. Please read all instructions carefully before use.

Figure 1: KATOOL KT-T900 Tire Changer and KT-B750 Wheel Balancer Combo.

Prìomh fheartan:

• KT-T900 Tire Changer: Fully hydraulic power system, built-in top assist arm, leverless design, stainless steel mounting head with plastic cover, assist wheel lift device, high-quality motor with pure copper winding.
• KT-B750 Wheel Balancer: Automatic measurement ruler for A and D values, robust 3mm thick steel body, all-in-one pressure sensor support design, top-level motor with pure copper winding, φ36mm shaft thread with quenching treatment, advanced welding technology computer board, various balance modes, built-in fault diagnosis and self-calibration, unit selection (Ounce/Gram, MM/Inch).

2. Suidhich

2.1 Unpacking agus Sgrùdadh

Carefully unpack all components. Inspect for any shipping damage. Report any damage to the carrier immediately.

2.2 Seanadh

While the wheel balancer requires minimal assembly, ensure all components are securely fastened. The tire changer requires assembly of its various arms and components. Refer to the included assembly diagrams for detailed steps.

2.3 Power and Air Connections

• KT-T900 Tire Changer: Connect to a 110V / 1PH / 60HZ power supply. Connect to an air compressor providing 0.8-1.0Mpa (116-145psi) air pressure.
• KT-B750 Wheel Balancer: Connect to a 120V 1PH power supply.
• Ensure all air hoses are securely connected and free of leaks. It is recommended to replace standard hose clamps with more robust alternatives if necessary to prevent leaks under pressure.

2.4 Placement and Securing

Position both machines on a level, stable surface. For optimal performance and safety, the KT-B750 Wheel Balancer should be bolted to the floor to prevent movement and ensure accurate measurements during operation.

3. Operating Instructions - KATOOL KT-T900 Tire Changer

The KT-T900 is designed for efficient and safe tire changing with its automatic hydraulic system.

Figure 2: KT-T900 Tire Changer demonstrating hydraulic arm movement.

3.1 Mounting and Demounting Tires

1. Suidheachadh na Cuibhle: Place the wheel onto the turntable. The wheel clamp can accommodate sizes from 12" to 30".
2. Clampa’ cur a’ chuibhle: Use the foot pedals to activate the rim clamps, a’ daingneachadh a’ chuibhle gu daingeann ris a’ chlàr-tionndaidh.
3. Briseadh nan grìogagan: Utilize the bead breaker arm to separate the tire beads from the rim. The hydraulic system ensures powerful and controlled operation.
4. Mounting/Demounting Head: Position the stainless steel mounting head (with plastic cover to protect rims) at the edge of the tire. The leverless design simplifies the process.
5. Using the Assist Arm: For difficult tires, such as run-flat or low-profile, engage the built-in top assist arm to help hold the tire bead in place.
6. Cuairteachadh: Use the foot pedal to rotate the turntable, allowing the mounting head to smoothly remove or install the tire.
7. Inflation (Bead Blaster): For stubborn beads, the integrated bead blaster can be used to quickly seat the tire. Ensure proper safety precautions are followed.

4. Operating Instructions - KATOOL KT-B750 Wheel Balancer

The KT-B750 provides precise wheel balancing with its automatic measurement ruler and various balancing modes.

Figure 3: KT-B750 Wheel Balancer control panel and wheel mounting.

4.1 Mounting the Wheel

1. Ensure the balancer is powered on.
2. Mount the wheel securely onto the balancer's shaft. Use appropriate cones and a quick-release nut to center and hold the wheel.

4.2 Inputting Wheel Dimensions

1. Use the automatic measurement ruler to input the 'A' (distance from machine to rim) and 'D' (rim diameter) values. The ruler will automatically detect and display these values on the control panel.
2. Manually input the 'W' (wheel width) value using the control panel buttons.
3. Select the desired balancing mode (e.g., Dynamic for clip-on weights on both sides, Static for single-plane balancing) using the control panel.

4.3 Balancing Process

1. Close the wheel guard (if equipped) and press the START button. The machine will spin the wheel to measure imbalance.
2. The display will show the required weight amounts and their positions (indicated by the laser pointer).
3. Apply the indicated weights to the inner and/or outer edges of the rim as directed.
4. Spin the wheel again to verify the balance. Repeat the process if necessary until the display shows zero or minimal imbalance.

5. Cumail suas

Nì cumail suas cunbhalach cinnteach gum mair an uidheam KATOOL agad fad-beatha agus gum bi e ag obair gu math.

5.1 Glanadh Coitcheann

• Keep both machines clean and free of dirt, dust, and tire debris.
• Sguab uachdar sìos le adamp cloth. Avoid using harsh chemicals that may damage finishes or electronic components.

5.2 Lubrication

• Tire Changer: Periodically lubricate moving parts, such as the assist arm joints and clamping mechanisms, according to the manufacturer's recommendations.
• Siostam adhair: Ensure the air filter/regulator unit (if present) is regularly oiled. The instruction label on the unit advises frequent oiling to the oil cup and to release water.

5.3 Air System Inspection

• Regularly check all air hoses and connections for leaks. Replace any worn or damaged hoses and ensure clamps tèarainte.
• Monitor the air pressure gauge to ensure it operates within the specified range.

6. A ’dèanamh trioblaid

Tha an earrann seo a’ dèiligeadh ri cùisean cumanta a dh’ fhaodadh tu a thighinn tarsainn orra.

6.1 Tire Changer Issues

• Difficulty with Bead Breaking/Mounting: Ensure proper lubrication of tire beads. Verify adequate air pressure to the machine. Utilize the assist arm for low-profile or stiff tires.
• Aoidion adhair: Inspect all pneumatic connections, especially hose clamps. Replace any damaged hoses or fittings.

6.2 Wheel Balancer Issues

• Leughaidhean neo-mhearachdach: Ensure the machine is bolted securely to a level floor. Verify correct input of wheel dimensions (A, D, W). Perform the self-calibration program if readings are consistently off.
• Inneal gun tòiseachadh: Thoir sùil air na ceanglaichean cumhachd agus dèan cinnteach gu bheil an suidse cumhachd air.

7. Sònrachaidhean

KATOOL KT-T900 Automatic Hydraulic Tire Changer

KATOOL KT-B750 Automatic Measurement Ruler Wheel Balancer

Fiosrachadh coitcheann toraidh

• Dèanadair: KATOOL
• Modail: KT-T900+KT-B750
• Cuideam nì: 622 not
• Meudan toraidh: 53 x 36 x 60 òirleach

8. Barantas agus Taic

Your KATOOL product is supported by the manufacturer and seller.

• Poileasaidh Tilleadh: Faodar an toradh seo a thilleadh gu 31 Faoilleach 2026.
• Taic teachdaiche: For any inquiries or assistance, please contact customer support.
• Dèanadair: KATOOL
• Neach-reic: Rainier Engineering, LTD