Allotech 4 Channel 433MHz Garage Door Remote Control

1. Ro-ràdh

This manual provides instructions for the Allotech 4 Channel 433MHz Garage Door Remote Control. This device is designed to operate compatible garage doors and gates, offering a convenient and portable solution for access control. Please read these instructions carefully before attempting to set up or operate your remote control.

Dealbh 1.1: Aghaidh view of the Allotech 4 Channel 433MHz Garage Door Remote Control. It features a black casing with a metallic silver panel and a keyring attachment.

2. Toradh thallview

2.1 Feartan

• 4-channel operation for controlling multiple devices.
• 433 MHz frequency for reliable signal transmission.
• Dealbhadh compact agus so-ghiùlain.
• Easy self-programming process.

2.2 Co-fhreagarrachd

This remote control is compatible with various garage door and gate automation systems operating at 433 MHz. It is designed to replace original remote controls from the following brands:

• Motorlift
• Àrdaichear
• Wayne-Dalton
• Chamberlain

Important Note: This remote control is NOT compatible with Motorlift ML500, ML1000, ML5500, or PP60 series systems, nor with 4410e-433 models.

Dealbh 2.1: Visual representation of compatible remote control models, including various Motorlift, Liftmaster, Wayne-Dalton, and Chamberlain models.

3. Suidheachadh agus Prògramadh

The Allotech remote control can be programmed directly from your existing garage door or gate opener. The process varies slightly depending on the specific model of your opener.

Dealbh 3.1: Diagram illustrating the programming steps for various compatible Chamberlain and Liftmaster systems.

3.1 Programming for Chamberlain / Liftmaster 4335-E

1. Press and hold any button on your new Allotech remote control.
2. While holding the button on the new remote, simultaneously press the 'Smart' button located on the back of your garage door motor.
3. The door opener light will turn on and then immediately turn off.
4. Release the button on your Allotech remote control. Your remote is now registered.

To Erase All Remote Controls (Chamberlain / Liftmaster 4335-E):

1. Press and hold the 'Smart' button on the opener's control panel.
2. Continue holding until the green indicator light on the side turns off (approximately 6 seconds).
3. All previously memorized codes will be erased. To reprogram, repeat the steps above.

3.2 Programming for Chamberlain / Liftmaster 94335-E

1. Press and release the 'Learn' button on the motor of your garage door opener.
2. The 'Learn' indicator light will illuminate continuously for 30 seconds.
3. Within these 30 seconds, press any button on your new Allotech remote control.
4. Release the button when the motor light flashes. Your remote is now registered.

To Erase All Remote Controls (Chamberlain / Liftmaster 94335-E):

1. Press and hold the 'Learn' button until the 'Learn' indicator light turns off (approximately 6 seconds).
2. All remote controls are now erased.

4. Obrachadh

Once programmed, operating your Allotech remote control is straightforward:

• Press the programmed button on the remote control to activate your garage door or gate.
• Each button can be programmed independently to control a different device, up to four devices in total.

Dealbh 4.1: Air ais view of the Allotech remote control, showing the four distinct buttons for channel operation.

5. Cumail suas

5.1 Ath-nuadhachadh bataraidh

The remote control uses an Alkaline battery. If the remote's range decreases or it stops responding, the battery may need replacement. To replace the battery:

1. Fosgail an smachd iomallach gu faiceallach casing.
2. Thoir air falbh an t-seann bataraidh.
3. Insert a new Alkaline battery, ensuring correct polarity.
4. Dùin an casing gu tèarainte.

Cuir às do sheann bataraidhean gu cùramach a rèir riaghailtean ionadail.

6. A ’dèanamh trioblaid

6.1 Chan eil an inneal-iarainn a’ freagairt

• Thoir sùil air bataraidh: Dèan cinnteach gu bheil am bataraidh air a chuir a-steach gu ceart agus gu bheil cosgais gu leòr ann. Cuir fear ùr na àite ma tha sin riatanach.
• Reprogram: The remote may have lost its programming. Follow the programming steps in Section 3.
• Co-chòrdalachd: Verify that your garage door or gate opener is listed as compatible. Refer to Section 2.2.
• Raon: Ensure you are within the operational range of the receiver (up to 10 meters).

6.2 Multiple Remotes Issues

Some motorization receivers have a limited capacity for registered remote controls (typically 3 to 15). If you experience issues with new remotes not registering or old ones ceasing to work, the receiver's memory might be full or corrupted due to incorrect programming attempts.

• Perform a Full Reset: Erase all remote controls from your opener's memory (refer to Section 3.1 or 3.2 for 'To Erase All Remote Controls').
• Reprogram All Remotes: After a full reset, reprogram all desired remote controls, starting with the new ones.

7. Sònrachaidhean

Dealbh 7.1: Diagram illustrating the dimensions of the Allotech remote control: 63 mm in length and 35 mm in width.

8. Barantas agus Taic

For information regarding warranty coverage or technical support, please refer to the product packaging or contact your retailer. Keep your purchase receipt as proof of purchase.