ACT Dual Hard Drive Docking Station

Ro-ràdh

The ACT AC1504 Dual Hard Drive Docking Station provides a convenient and efficient solution for connecting and accessing 2.5-inch and 3.5-inch SATA I/II/III hard drives and SSDs. This device supports high-speed data transfer via USB 3.0 (USB 3.2 Gen1) and features an offline cloning function, allowing you to duplicate drives without a computer connection. It is designed for data transfer, storage expansion, file backup, data recovery, system upgrades, and disk cloning.

Susbaint pacaid

Dèan cinnteach gu bheil a h-uile nì an làthair sa phacaid agad:

• ACT Dual Hard Drive Docking Station (AC1504)
• USB 3.0 Type-A to Type-B Cable
• Adapter cumhachd
• Leabhar-làimhe cleachdaiche (an sgrìobhainn seo)

Image: The ACT AC1504 Dual Hard Drive Docking Station, its power adapter, and the USB 3.0 cable, as included in the package.

Feartan toraidh

• Dual Bay Compatibility: Supports all 2.5-inch and 3.5-inch SATA I/II/III HDDs and SSDs up to 12.5mm thickness.
• USB 3.0 Àrd-astar: Utilizes USB 3.2 Gen1 technology for ultra-fast data transfer rates up to 5 Gbps.
• Taic UASP: Enhanced performance with USB Attached SCSI Protocol.
• Offline Cloning: Clone data from one hard drive to another without requiring a computer connection.
• Cleachdadh ioma-chruthach: Ideal for data transfer, storage expansion, file backup, data recovery, system upgrades, and disk cloning.

Suidhich

1. Ceangal cumhachd: Plug the power adapter into the DC input port on the rear of the docking station. Connect the other end of the power adapter to a wall outlet.
2. Cuir a-steach draibhearan cruaidh: Gently slide your 2.5-inch or 3.5-inch SATA HDD/SSD into the drive slots. Ensure the drives are fully seated. For offline cloning, the source drive should be in the 'Source' slot and the target drive in the 'Target' slot.
3. Connect to Computer (for data access): If you intend to use the docking station for data access via your computer, connect the USB 3.0 cable from the docking station's USB port to an available USB port on your computer.
4. Cumhachd air: Flip the ON/OFF switch on the rear of the docking station to the 'ON' position. The power indicator LED will illuminate.

Image: Rear panel of the docking station, illustrating the USB 3.0 port, ON/OFF power switch, and DC power input for connections.

Image: The docking station connected to a laptop via its USB cable, with two hard drives inserted, demonstrating a typical setup for data access.

Stiùireadh Obrachaidh

A. Data Access Mode (Connected to Computer)

1. Dèan cinnteach gu bheil an stèisean docaidh air agus ceangailte ris a’ choimpiutair agad tron ​​chàball USB 3.0.
2. Insert one or two SATA HDDs/SSDs into the available slots.
3. Bu chòir don t-siostam obrachaidh agad na draibhearan a lorg gu fèin-ghluasadach. Nochdaidh iad mar innealan stòraidh a ghabhas toirt air falbh.
4. Faodaidh tu a-nis faighinn gu, gluasad agus riaghladh files on the inserted drives as you would with any other external storage.

B. Offline Cloning Function

The offline cloning function allows you to duplicate a source drive to a target drive without a computer connection.

1. Ullaich Draibhean: Ensure both the source drive (the drive you want to copy FROM) and the target drive (the drive you want to copy TO) are SATA HDDs/SSDs. The target drive must be equal to or larger in capacity than the source drive.
2. Cuir a-steach Draibhean: Insert the source drive into the 'Source' slot (HDD1) and the target drive into the 'Target' slot (HDD2).
3. Dì-cheangail bhon PC: Ensure the docking station is NOT connected to any computer via USB.
4. Cumhachd air: Tionndaidh air an stèisean docaidh a’ cleachdadh an suidse ON/OFF.
5. Tòisich air clònadh: Press and hold the 'Clone' button for approximately 3-5 seconds until the cloning progress LEDs (25%, 50%, 75%, 100%) begin to flash.
6. Dearbhaich clònadh: Release the button, then quickly press it again to confirm the cloning process. The cloning process will begin, indicated by the progress LEDs lighting up sequentially.
7. Sùil air adhartas: The LEDs will indicate the cloning progress (25%, 50%, 75%, 100%). All LEDs will remain solid when the cloning process is complete.
8. Cumhachd dheth: Once cloning is complete, turn off the docking station and safely remove the drives.

Cudromach: All data on the target drive will be erased during the cloning process. Back up any important data from the target drive before initiating cloning.

Image: The ACT AC1504 Dual Hard Drive Docking Station with two hard drives inserted, illustrating its dual-bay design and the LED indicators for power, activity, and cloning progress.

Cumail suas

• Cùm an stèisean docaidh glan agus saor bho dhuslach. Cleachd clò bog, tioram airson a ghlanadh.
• Seachain an inneal a nochdadh gu fìor theodhachd, taiseachd, no solas dìreach.
• Na feuch ri an inneal a thoirt às a chèile no a chàradh thu fhèin. Cuir fios gu luchd-obrach seirbheis teisteanasach.
• Always power off the docking station before inserting or removing drives, especially during data transfer, to prevent data corruption.

Fuasgladh thrioblaidean

• Draibh gun lorg:
  • Ensure the docking station is powered on and the drive is properly seated in the slot.
  • Verify the USB cable is securely connected to both the docking station and your computer.
  • Feuch ri ceangal a dhèanamh ri port USB eile air a’ choimpiutair agad.
  • Check if the drive is initialized and formatted in your computer's Disk Management (Windows) or Disk Utility (macOS).
• Gluasad dàta mall:
  • Dèan cinnteach gu bheil thu ceangailte ri port USB 3.0 air a’ choimpiutair agad. Bidh puirt USB 2.0 a’ ciallachadh gum bi astaran nas slaodaiche.
  • Dearbhaich gu bheil an siostam obrachaidh agus na draibhearan agad a’ toirt taic do USB 3.0 agus UASP.
• Dh’fhàillig clònadh far-loidhne no cha do thòisich e:
  • Ensure the docking station is NOT connected to a computer via USB during cloning.
  • Confirm the target drive's capacity is equal to or larger than the source drive's capacity.
  • Make sure both drives are properly inserted and detected by the docking station (power and activity LEDs should be on).
  • Follow the cloning steps precisely, especially the press-and-hold and quick-press sequence for the 'Clone' button.

Sònrachaidhean

Barantas agus Taic

ACT provides reliable connectivity solutions. All ACT products comply with international standards and EU legislation. This product benefits from a factory warranty of 2 to 5 years.

For technical support or warranty claims, please refer to the official ACT weblàrach no cuir fios chun neach-reic ionadail agad.

Weblàrach: www.act-connectivity.com