Apevia Genesis Pro G-PRO-BK Mid Tower Gaming Case Instruction Manual

1. Setup agus Stàladh

1.1 Fo-phacadh agus Ullachadh

Carefully remove the case from its packaging. Place it on a stable, flat surface. Identify all included accessories, such as screws, standoffs, and cable ties.

Figure 1: Apevia Genesis Pro G-PRO-BK with side panel open.

The case features two tempered glass panels: one on the left side and one on the front. The left side panel is typically secured with thumbscrews at the rear, while the front panel may be magnetically attached or secured with clips. Exercise caution when handling glass panels to prevent damage.

1.2 Stàladh Motherboard

1. Install the necessary standoffs for your motherboard form factor (ATX, Micro-ATX, or Mini-ITX). The case supports standard ATX, Micro-ATX, and Mini-ITX motherboards.
2. Place the I/O shield into the rear opening of the case.
3. Carefully align your motherboard with the standoffs and I/O shield, then secure it with screws.

1.3 Stàladh Solar Cumhachd

The power supply mounts at the top of the case. Secure your power supply unit (PSU) into the designated bay using the provided screws.

1.4 Stàladh Draibh Stòraidh

The case supports up to two 3.5-inch hard drives and two 2.5-inch solid-state drives (SSDs). Locate the drive bays and secure your storage devices using the appropriate screws.

Figure 2: Internal layout with drive bay locations and cable management options.

1.5 Stàladh Cairt Grafaigean (GPU)

Install your graphics card into the appropriate PCIe slot on your motherboard. The case supports video cards up to 350mm in length. Secure the GPU with the expansion slot screws.

1.6 Stàladh Siostam Fuarachaidh (Luchd-leantainn & Rèididheatoran)

The Genesis Pro G-PRO-BK comes with six pre-installed 120mm RGB fans. It supports up to six 120mm fans in total and up to 240mm radiators in the top and front positions. CPU coolers up to 160mm in height are supported.

Figure 3: Airflow diagram for optimal cooling.

Ensure all fans are connected to the fan hub or motherboard headers for power and RGB control.

1.7 Stiùireadh Càbaill

Utilize the cable routing cutouts and tie-down points behind the motherboard tray to manage cables neatly. This improves airflow and aesthetics.

2. Stiùireadh Obrachaidh

2.1 A’ cur cumhachd air adhart

After all components are installed and connected, ensure the power supply switch is in the 'ON' position. Press the power button located on the top I/O panel to start your system.

Figure 4: Top I/O panel with power and control buttons.

2.2 Smachd Solais RGB

The pre-installed RGB fans can be controlled via the "LED" button on the top I/O panel. This button cycles through 16 lighting modes, offering 30 total play-through options including RGB, Breathing, Single Color, and Light Off. The fans are proprietary to this case.

Figure 5: Detail of an RGB fan, showcasing its lighting capabilities.

3. Cumail suas

3.1 Glanadh sìoltachain duslach

The case includes a magnetic dust filter on the top panel. Regularly remove and clean this filter to maintain optimal airflow and prevent dust buildup inside the system. Gently wash with water and mild soap, then allow to air dry completely before reattaching.

Figure 6: Top panel with magnetic dust filter.

3.2 Glanadh Coitcheann

Use a soft, dry cloth to wipe down the exterior of the case. For tempered glass panels, use a glass cleaner and a microfiber cloth. Avoid abrasive cleaners or solvents that could damage the finish.

4. A ’dèanamh trioblaid

4.1 Siostam gun a bhith a’ tionndadh air

• Ensure the power supply is properly connected to the wall outlet and the PSU switch is 'ON'.
• Verify all power cables (24-pin ATX, CPU, GPU, etc.) are securely connected to the motherboard and components.
• Thoir sùil air ceanglaichean ceann-sgrìobhaidh a’ phannal aghaidh ris a’ bhòrd-màthair (Power SW, Reset SW).

4.2 RGB Fans Not Lighting Up or Functioning

• Confirm that the fan hub (if used) is receiving power and is correctly connected to the motherboard or power supply.
• Ensure all fan RGB cables are properly connected to the fan hub or motherboard RGB headers.
• Press the "LED" button on the top I/O panel to cycle through lighting modes.

4.3 Cùisean Cus-theasachaidh

• Verify that all case fans are spinning correctly and are oriented for optimal airflow (intake/exhaust).
• Clean all dust filters and internal components to remove any dust buildup.
• Dèan cinnteach gu bheil fuaradair an CPU agus luchd-leantainn an GPU ag obair ceart.

5. Sònrachaidhean

Figure 7: Internal dimensions and component compatibility.

6. Barantas agus Taic

For warranty information and technical support, please refer to the official Apevia weblàrach-lìn no cuir fios chun t-seirbheis teachdaiche aca gu dìreach. Cùm dearbhadh do cheannach airson tagraidhean barantais.

Apevia is a U.S. based computer hardware brand delivering reliable, performance-driven PC components. Specializing in PC cases, power supplies, and cooling solutions, Apevia brings modern design, efficiency, and affordability for gamers, creators, and builders.