Sunkko 788H LED Dual Pulse Spot Welder & Battery Charger User Manual

1. Stiùireadh Sàbhailteachd Cudromach

Read all safety warnings and instructions carefully before operating this device. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Solar cumhachd: The Sunkko 788H requires a robust power supply. The rated current of the leakage protection switch should be over 60A. Use of this device with standard household circuits (typically 20A maximum) is not recommended and may cause circuit breakers to trip or damage to the electrical system.
• Fionnarachadh: Operate the welder in a well-ventilated area to prevent overheating and accumulation of fumes.
• Dìon sùla: Always wear appropriate eye protection (e.g., welding goggles or face shield) to protect against sparks and intense light.
• Sàbhailteachd dealain: Na obraich an inneal le làmhan fliuch no ann an damp conditions. Ensure all connections are secure before powering on.
• Electrode Handling: Electrodes can become hot during operation. Allow them to cool before handling or adjusting.
• Clann is Peataichean: Cùm an inneal a-mach à ruigsinneachd chloinne is pheataichean.
• Cleachdadh ceart: Use the device only for its intended purpose of spot welding and battery charging/testing.

2. Pasgan-susbaint

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your supplier.

Ìomhaigh: Tharview of the Sunkko 788H spot welder and its standard included parts.

1. Sunkko 788H Spot Welder Unit (1 set)
2. Leabhar-làimhe Cleachdaiche (1 pc)
3. Hex Wrench (1 pc)
4. Fuse Tube (2 pcs)
5. Welding Pins (2 pairs)
6. Charging Wires (2 pcs)
7. Fixture for 6 Batteries (1 pc)
8. Nickel Sample Strips (100 pcs)
9. Foot Pedal Switch (1 pc)
10. Càball cumhachd (1 pc)

3. Toradh thallview

The Sunkko 788H is a versatile dual-pulse spot welder and battery charger designed for assembling battery packs, particularly 18650 cells, and for general spot welding applications. It features precise microcomputer control for welding parameters and an adjustable charging function.

Image: The Sunkko 788H LED Dual Pulse Spot Welder and its accessories.

Image: Close-up of the Sunkko 788H front control panel, showing displays and adjustment knobs.

Prìomh fheartan:

• Microcomputer controlled dual-pulse spot welding.
• Adjustable welding current (50-800A) and pulse time (1ms-19ms).
• Integrated battery charger with adjustable voltage (4.2-36V) and current (0-3A).
• Battery testing function to measure voltage.
• Foot pedal for precise welding control.
• Adjustable welding pressure knob for consistent welds.

4. Suidhich

Follow these steps to set up your Sunkko 788H unit before first use.

1. A' dì-phapadh: Thoir a h-uile pàirt a-mach às a’ phacaid gu faiceallach. Cùm am pasgan airson stòradh no còmhdhail san àm ri teachd.
2. Suidheachadh: Place the unit on a stable, flat, and non-flammable surface in a well-ventilated area. Ensure there is adequate space around the unit for air circulation.
3. Ceangal cumhachd: Connect the power cable to the unit and then to a suitable 110V AC, 60Hz power outlet. Ensure the circuit can handle the required current (over 60A recommended).
   

   Ìomhaigh: Taobh view of the Sunkko 788H, showing ventilation and power input location.

4. Install Welding Pins: Insert the welding pins into the designated slots on the front of the unit. Secure them firmly using the provided hex wrench. Ensure the tips are aligned and clean.
   

   Image: Close-up of the welding terminals on the Sunkko 788H, where welding pins are inserted.
5. Ceangail Peadal Coise: Plug the foot pedal switch into the 'PEDAL INTERFACE' port on the front panel.
6. Adjust Welding Pressure: Use the knob on top of the unit to adjust the welding pressure. This knob controls the force applied by the welding pins. A typical range is 300g-750g. Adjust based on material thickness and desired weld quality.
   

   Image: Close-up of the welding pressure adjustment knob located on the top of the Sunkko 788H unit.

5. Stiùireadh Obrachaidh

5.1 Spot Welding Function

The 788H offers precise control over welding parameters for various materials, primarily nickel strips for battery pack assembly.

1. Cumhachd air: Flip the 'POWER' switch to the ON position. The display will illuminate.
2. Tagh Modh Tàthaidh: Ensure the 'WELDING / CHARGE' switch is set to 'WELDING'.
3. Suidhich an-dràsta: Use the 'SET CURRENT' knob to adjust the welding current. The display shows the current level (e.g., 0-99). Start with lower settings and increase gradually. For 0.1-0.2mm nickel strips, typical settings range from 50-800A.
4. Set Pulse Mode: The unit supports single or dual pulse welding. Adjust the pulse setting based on the material thickness and desired weld strength. Dual pulse is generally recommended for stronger, more consistent welds.
5. Ullaich stuthan: Clean the surfaces to be welded. Place the nickel strip over the battery terminal or other material.
6. Position Electrodes: Carefully position the welding pins onto the nickel strip, ensuring both pins make firm contact with the strip and the underlying material.
7. Tòisich air tàthadh: Press the foot pedal to initiate the weld. The unit will deliver the set pulse(s).
8. Sgrùdadh tàthaidh: After welding, inspect the joint for strength and appearance. Adjust current and pulse settings as needed. For pure nickel strips, 0.1-0.15mm thickness is typically supported effectively.

5.2 Battery Charging Function

The 788H can also function as an adjustable battery charger.

1. Tagh Modh Cosgais: Flip the 'WELDING / CHARGE' switch to 'CHARGE'.
2. Ceangail Bataraidh: Use the provided charging wires to connect the battery to the 'CHARGE' terminals (red for positive, black for negative).
3. Suidhich Voltage: Cleachd an 'VOLTAGE' knob to set the desired charging voltage (4.2V - 36V). Ensure this matches the battery's nominal voltage.
4. Suidhich an-dràsta: Use the 'CURRENT' knob to set the desired charging current (0A - 3A). A common charging rate is 0.5C to 1C of the battery's capacity.
5. Sgrùdadh cosgais: Bidh an taisbeanadh a’ sealltainn an voltage and current. Monitor the charging process and disconnect the battery once fully charged to prevent overcharging.

Image: Close-up of the battery charging and testing terminals on the Sunkko 788H.

5.3 Battery Testing Function

The unit can also test the voltage of connected batteries.

1. Tagh Modh Deuchainn: Ensure the 'WELDING / CHARGE' switch is set to 'CHARGE'.
2. Ceangail Bataraidh: Connect the battery to the 'TEST' terminals using the charging wires.
3. Leugh Voltage: Bidh an taisbeanadh a’ sealltainn an voltage of the connected battery. This can be used to check the battery's state of charge or identify faulty cells.

6. Cumail suas

Regular maintenance ensures the longevity and optimal performance of your Sunkko 788H.

• Glanadh: Cùm an aonad glan agus saor bho dhuslach is sprùilleach. Cleachd clò tioram, bog airson glanadh. Na cleachd innealan-glanaidh leaghaidh.
• Cùram Electrode: Regularly inspect the welding pins for wear or carbon buildup. Clean or sharpen the tips as needed to ensure good contact and consistent welds. Replace worn-out pins promptly.
• Fionnarachadh: Dèan cinnteach nach eil na sliotan fionnarachaidh air an aonad dùinte gus casg a chur air cus teasachadh.
• Stòradh: When not in use, store the unit in a dry, cool place away from direct sunlight and moisture.

7. A ’dèanamh trioblaid

This section addresses common issues you might encounter with the Sunkko 788H.

8. Sònrachaidhean Teicnigeach

9. Barantas agus Taic

Specific warranty information for the Sunkko 788H is not provided in the product details. For any warranty claims, technical support, or service inquiries, please contact the original seller or manufacturer directly. Retain your proof of purchase for any potential claims.