Leabhar-làimhe Cleachdaiche Tar-chuir Meur-chlàr Ioma-chòd Lìnearach 420001

Ro-ràdh

This manual provides instructions for the installation, operation, and maintenance of the Linear Multi-Code Keypad Transmitter, model 420001. This wireless keypad is designed for use with Multi-Code Receivers to control access to garage doors or gates.

Bathar seachadview

The Linear Multi-Code Keypad Transmitter 420001 is a 12-button alphanumeric keypad. It operates on a 300 MHz frequency and features 10 dip switches for programming. Its weatherproof casinTha g a’ dèanamh cinnteach à seasmhachd airson cleachdadh a-muigh.

Ìomhaigh: Aghaidh view of the Linear Multi-Code Keypad Transmitter 420001, showing the 12-button alphanumeric keypad and the "MULTI-CODE" branding at the top.

Stàladh agus stàladh

1. Stàladh bataraidh

   The keypad requires one 9V alkaline battery (not included). To install:

   • Open the keypad casing.
   • Connect the 9V battery to the battery clip.
   • Place the battery securely within the compartment.
   • Close the keypad casing, ensuring it is sealed properly for weather resistance.

2. A' cur suas

   The keypad is designed for screw-in installation and mounts with two screws.

   • Choose a suitable location for mounting, ensuring it is within range of your Multi-Code Receiver.
   • Mark the positions for the two mounting screws.
   • Dril tuill pìleat ma tha sin riatanach.
   • Secure the keypad to the surface using appropriate screws.

3. A ’prògramadh an Keypad

   This keypad uses 10 dip switches for programming. The code is entered directly through the keypad, eliminating the need to manually adjust physical dip switches on the unit itself.

   1. Locate the dip switch settings on your Multi-Code Receiver or existing remote. This will be a sequence of 10 switches, each set to ON, OFF, or MIDDLE (if applicable).
   2. On the 420001 keypad, enter the 10-digit code corresponding to your receiver's dip switch settings. Refer to the keypad's internal instructions for specific key presses to represent ON, OFF, or MIDDLE positions.
   3. Press the "ACCESS" button to save the code.
   4. Test the keypad to ensure it operates your garage door or gate opener.

   Thoir an aire: Programming typically takes less than 2 minutes. Ensure the keypad is within operational range of the receiver during testing.

Stiùireadh Obrachaidh

To operate your garage door or gate using the Linear Multi-Code Keypad Transmitter:

1. Enter your programmed 10-digit access code using the alphanumeric buttons.
2. Press the "ACCESS" button.
3. The LED indicator will illuminate, and your Multi-Code Receiver should activate, opening or closing your garage door or gate.

If the door or gate does not respond, verify your code and ensure the keypad is within effective range of the receiver.

Cumail suas

• Ath-nuadhachadh bataraidh: When the keypad's performance degrades or the LED indicator fails to light, replace the 9V battery. Follow the battery installation steps.
• Glanadh: Clean the keypad's exterior with a soft, damp clò. Seachain innealan-glanaidh sgrìobach no fuasglaidhean.
• Frith-aghaidh sìde: The keypad features a weatherproof casing. Dèan cinnteach gu bheil an casing is properly closed and sealed after any internal access (e.g., battery replacement) to maintain its weather-resistant properties.

Fuasgladh thrioblaidean

Sònrachaidhean

Barantas agus Taic

Airson fiosrachadh barantais no taic theicnigeach, thoir sùil air fiosrachadh oifigeil an neach-dèanamh. weblàrach-lìn no cuir fios chun roinn seirbheis teachdaiche aca. Cùm do chuidhteas ceannach airson tagraidhean barantais.

Dèanadair: Sreathach